79089

DeWalt D 28400 Manual

37
Zoom out
Zoom in
Previous page
1/174
Next page
ENGLISH
35
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fi g. 5, 6)
WARNING: Before using the tool,
check that the handle is tightened
securely.
For grinding, screw the side handle (e) tightly into
one of the holes (r) on either side of the gear case
(fig. 5).
For cutting, screw the side handle (e) tightly into the
top hole (s) or into one of the holes (t) on either side
of the gear case (fig. 6).
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded fl ange.
Mounting and Removing the Guard
(fi g. 2)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
CAUTION: Guards must be used with
this grinder.
When using the D28400 or the D28401 grinder for
cutting metal or masonry a Type 1 guard MUST be
used. Type 1 guards are available at extra cost from
DEWALT distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
show other accessories that can be used with these
grinders.
1. Place the angle grinder on a table, spindle (o)
up.
2. Release the clamping lock (f) and hold the guard
(d) over the tool as shown.
3. Align the lugs (k) with the notches (l).
4. Press the guard (d) down and rotate it to the
required position.
5. Fully close the clamping lock (f)
6. Ensure screw (m) is fastened tightly and the
guard is fixed
7. To remove the guard, reverse the above
instructions.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
Fitting and Removing a Grinding or
Cutting Disc (fi g. 1, 3, 4)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (i) correctly onto the
spindle (o) (fig. 3).
3. Place the disc (n) on the backing flange (i).
When fitting a disc with a raised center, make
sure that the raised centre (j) is facing the
backing flange (i).
4. Screw the threaded clamp nut (h) onto the
spindle (o) (fig. 4):
a. The ring on the threaded clamp nut (h) must
face towards the disc when fitting a grinding
disc (fig. 4A);
b. The ring on the threaded clamp nut (h) must
face away from the disc when fitting a cutting
disc (fig. 4B).
5. Press the spindle lock button (c) and rotate the
spindle (o) until it locks in position.
6. Tighten the threaded clamp nut (h) with the two-
pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (h) with the two-pin spanner.
Prior to Operation
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flange are mounted
correctly.
• Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D 28400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D 28400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 25,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info