Manual DeWalt d 28151 k (page 23 of 92) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

390548

Zoom out

Zoom in

1/92

ENGLISH

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Mounting and removing the guard (fig. B)

• Place the angle grinder on a table, spindle up.

• Release the clamping lock (6) and hold the guard

(4) over the tool as shown.

• Align the lugs (7) with the notches (8).

• Press the guard down and rotate it to the

required position.

• If required, increase the clamping force by

tightening the screw (9).

• Tighten the clamping lock.

• To remove the guard, release the clamping lock.

Never use the tool without the guard in

place.

Fitting and removing a grinding or cutting disc

(fig. C1 & C2)

• Place the tool on a table, guard up.

• Fit the inner flange (10) correctly onto the spindle

(11) (fig. C1).

• Place the disc (12) on the flange (10). When

fitting a disc with a raised center, make sure that

the raised centre (13) is facing the flange (10).

• Screw the outer flange (14) onto the spindle (11)

(fig. C2):

- the ring on the flange (14) must face towards

the disc when fitting a grinding disc (A);

- the ring on the flange (14) must face away from

the disc when fitting a cutting disc (B).

• Press the spindle lock (3) and rotate the spindle

(11) until it locks in position.

• Tighten the flange (14) with the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the disc, loosen the flange (14) with

the two-pin spanner.

Do not use a damaged disc.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the spindle

without using the spacer and threaded flange.

Mounting and removing the rubber backing pad

(fig. D)

The rubber backing pad is available as an option.

• Remove the guard from the tool.

• Press the backing pad (15) onto the spindle (11).

The inner flange is not needed.

• Position the abrasive disc (16) on the pad.

• Screw the outer flange (14) onto the spindle (11).

• Press the spindle lock and rotate the pad (15)

until it locks in position.

• Tighten the flange (14) using the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the pad, loosen the flange (14) with

the two-pin spanner.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d 28151 k in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt d 28151 k Manual

Product: