658408
63
Zoom out
Zoom in
Previous page
1/259
Next page
30 VIII User Manual Pedelec Xion
10 Cleaning
Remove the battery before you clean your
Pedelec.
Do not use benzine, thinner, acetone or similar
agents in the cleaning procedures under any
circumstances. Likewise, the use of abrasive
cleaners and aggressive cleaning agents must
also be avoided.
Only use commercially available, household
cleaning agents and disinfectants (isopropyl
alcohol) or water. You can obtain suitable clean-
ing agents and additional information om your
specialist cycle shop.
We recommend you clean your Pedelec with a
damp cloth, a sponge or a brush.
10.1 Cleaning the battery
Make sure when cleaning that water does not enter the
battery. Although the electrical components are sealed,
it is not advisable to clean the bike by spraying it with a
hose or a high-pressure cleaner. This could damage your
bike.
When wiping down the battery, be carel not to touch and
connect the contacts on the underside. This could cause
the battery to switch o.
10.2 Cleaning the motor
Dirt should be removed om the motor of your Pedelec
regularly, ideally using a dry brush or a damp (not wet)
cloth. Running water such as that om a hose pipe or even
a high-pressure cleaner must not be used for cleaning.
The ingress of water can destroy the motor. Therefore,
ensure that neither uids nor moisture enter the motor at
any time during cleaning.
Do not clean the motor when it is warm, e.g. immediately
aer a trip. Wait until it has cooled down. Otherwise, the
motor may be damaged.
9.2 Installing the rear wheel
1. Place the torque support on the le axle side of the
motor (see point 2 in the image below).
2. Then feed the rear wheel past the rear derailleur and
into the dropout on the ame.
3. If your Pedelec has disc brakes, ensure that the brake
disc is placed exactly in the centre between the brake
blocks.
4. Insert the rear wheel in the dropout so that the torque
support ts exactly and the ends of the axle sit entirely
within the dropout.
5. Close the quick-release device ( General User Manu-
al, Chapter 18.6.2 “Inserting the rear wheel ”).
6. Connect the cable between the motor and the battery.
7. Attach the plug to the chain stay once more
using the rubber ring.
8. If your Pedelec has rim brakes, engage the brake cable
once more.
For precise details regarding the handling of rim or
disc brakes and quick-release devices, please refer to
the section of the User Manual concerning the tech-
nology featured in the bike.
Placing the torque support
Motormontage - Bremsseite
Motor mounting - side of the brake
ALBER-Komponenten
Komponenten anderer Hersteller
[1] Motor
[2] Drehmomentstütze in der von Ihnen bestellten Variante (Abweichung zur Grafik möglich)
Rahmen des Fahrrads
[3] Unterlagscheibe
[4] Mutter,
[5] Bremsscheibe
[6] Bremsensatz
[7]
Anzugsmoment: 20 Nm
ACHTUNG: Zuerst die Mutter auf der gegenüberliegenden Seite anziehen, danach diese Mutter!
Bitte beachten Sie bei Ihren Arbeiten die Vorgaben und Empfehlungen des jeweiligen Herstellers zur
Montage seiner Komponenten.
ALBER Components
Components of other manufacturers
[1] Motor
[2] Torque receiver in the version ordered (might differ from drawing)
[3] Washer
[4] Nut,
[5] Brake disc
[6] Brake set
[7] Bicycle frame
fastening torque: 20 Nm
Please pay attention to the instructions of each manufacturer for the assembly of the appropriate
components.
ATTENTION: Tighten this nut after the one on the opposite!
5
6
3
4
1
2
7
4
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Derby Cycle Pedelec Xion 2013 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Derby Cycle Pedelec Xion 2013 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 19,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info