498829

Denver CAD-471 Manual

12
Zoom out
Zoom in
Previous page
1/12
Next page
RESET
3. Press and hold SEL button again.
4. Using volume knob, enter the name of the contact. Press SEL button to save each character entered.
5. Enter the phone number. Press SEL button to save each number entered.
6. Press and hold SEL button to save entry.
Finding Contacts
After adding contacts, you can use this feature to find them.
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “FIND NUM” displays.
3. Press and hold SEL button again.
4. Using volume knob, select the name of the contact and press to call.
Deleting Contacts
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “FIND NUM” displays.
3. Press and hold SEL button again.
4. Rotate VOL knob until the name of the contact you want to delete displays.
5. Press and hold “ ” for 2 seconds to delete contact.
How to Set Incoming Call Melody
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “MELODY” displays.
3. Rotate VOL knob to the desired melody.
How to Set Incoming Call Ring Volume
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “RING” displays.
3. Rotate VOL knob to the desired level.
How to Set Conversation Volume
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “TEL” displays.
3. Rotate VOL knob to the desired level.
Disconnect Paired Devices
You can disconnect to an already paired Bluetooth device from your car stereo.
1. Press and hold (*) then press and hold SEL button for 2 seconds.
2. Press SEL button repeatedly until “DISCONN” displays.
3. Press and hold SEL button again to disconnect.
• RESET
Reset button is placed on the housing.
The reset button is to be activated for the following reason:
• Initial installation of the unit when all wiring is completed.
• All the function button do not operate.
• Error symbol on the display.
Instructions on environment protection
Do not dispose of this product in the usual household garbage at the end of its lifecycle; hand it over at a collection
point for the recycling of electrical and electronic appliances. The symbol on the product, the instructions for use or
the packing will inform about the methods for disposal.
The materials are recyclable as mentioned in this marking. By recycling, material recycling or other forms of re-
utilization of old appliances, you are making an important contribution to protect our environment.
Please inquire at the community administration for the authorized disposal location.
ALL RIGHTS RESERVED
COPY RIGHT DENVER ELECTRONICS A/S
www.denver-electronics.com
Note: Specication and the design are subject to possible modication without notice due to improvements.
TECHNICAL SPECIFICATIONS
CD/MP3 PLAYER SECTION
Signal to Noise Ratio > 60 dB
Channel Separation > 50 dB (1kHz)
Frequency Response 20Hz - 20 kHz
TUNER (FM)
Frequency range 87.5-108 MHz
Intermediate frequency 10.7 MHz
Sensitivity 2.8 µV
Stereo separation 30 dB
Signal to noise ratio 50 dB
Channel step 50 kHz
LINE-OUT
Output 350 mV
Impedance 10k Ohm
GENERAL
Power Supply 12V DC (10.8-15.6V) allowable)
Speaker impedance 4 or 8 Ohm
Output power 40W x 4CH
… 12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denver CAD-471 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denver CAD-471 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denver CAD-471

Denver CAD-471 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info