668295

Denon VL12 Prime DJ Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
Setup
Platter
Place the platter onto the motor by aligning the pins in the bottom of the
platter with the holes in the motor. Press it down firmly. Check to make sure
that it rotates uniformly and does not wobble excessively, and then place the
slipmat onto the platter.
Important:
• Incorrect platter setup can lead to poor turntable performance, platter
instability or permanent motor damage.
• Make sure that the felt slipmat is always placed on top of the platter while
using the turntable. Failure to use the slipmat may cause damage to your
media as well as damage to the turntable.
Tonearm
0 360° 1
2345
Important: Refer to the documentation for your cartridge to determine the proper stylus
pressure/weight (in grams) and tonearm height (in millimeters).
1. Make sure the cartridge is on the tonearm. Turn it clockwise to loosen it or counterclockwise to
tighten it. Do not over-tighten it! Remove the plastic cartridge cover (needle cover) before
operating the turntable.
2. Attach the counterweight and scale ring to the tonearm, and then rotate the counterweight
counterclockwise (while you are facing the scale ring) until it is in the complete forward position.
Note: This is also the maximum amount of pressure that can be applied to the cartridge.
3. Now there should be a feeling of weight and resistance when the headshell is raised and
lowered. Begin rotating the counterweight clockwise (while you are facing the scale ring) until
the weight and resistance feeling is gone. If done properly, the tonearm will pivot with very little
resistance back and forth indicating that there is exactly 0 grams of stylus pressure.
4. With the counterweight in its new position further away from tonearm pivot point, grasp the
scale ring only and rotate it until 0 is in the vertical position.
5. Finally, rotate the counterweight and scale ring counterclockwise until you reach the desired
weight. A complete revolution of the scale ring corresponds to 3 g, so if the scale rotates 360°
beyond the 0 point, add 3 to the new scale ring reading.
If you cannot achieve the desired weight during this step, remove the counterweight and scale
ring from the tonearm entirely, attach the additional counterweight (included) to the end of the
tonearm, and then start again from Step 2 above. This is not a common occurrence, though
there may be some DJ headshells and cartridges that are heavier than normal.
6. Push the small Lock lever (above the Anti-Skate Dial) counterclockwise to unlock the height
adjustment dial. Place the stylus on your record, and then move the tonearm lever to raise or
lower the tonearm so it is parallel with the record. Push the Lock lever clockwise to lock the
height adjustment dial.
4 g
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon VL12 Prime DJ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon VL12 Prime DJ in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 6,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info