543133
9
Zoom out
Zoom in
Previous page
1/26
Next page
ENGLISH
ENGLISH ENGLISH
Getting Started
4
q Power operation switch (ON/STANDBY)
When pressed, the power turns on and the display lights.
The muting mode is set for several seconds, after which
the TU-1500AE will function normally.
When pressed again, the power is set to the “standby”
mode and the display turns off.
w STEREO indicator
In the AUTO mode, this lights when a stereo broadcast is
tuned in. ( page 9)
e TUNED indicator
This lights when the strength of the reception frequency is
at or above a specific level. ( page 9)
r RDS indicator
This lights when receiving RDS broadcasts, and flashes
during the RDS search. ( page 11 ~ 14)
t ON/STANDBY indicator
This lights when the TU-1500AE’s power is in the “on” or
“standby” mode.
y Remote control sensor
This is the remote control signal sensor.
u Display
i DIMMER button
The display’s brightness can be adjusted in three steps.
Press this button to switch the brightness between high,
medium and low, in that order.
o BAND button
Press this button to switch the band between FM and AM.
( page 9)
!0 AUTO PRESET button
When pressed while the FM band is set, the TU-1500AE
searches for stations that can be received in stereo and up
to 100 stations are automatically stored at the preset
channels. (The stations are stored in order starting from
channel A1.) ( page 8)
!1 MENU button
Press this button to set the MENU mode. ( page 10 ~
15)
!2 TUNING/PRESET knob
When in the tuning mode, use this knob to raise or lower
the frequency. Turn the knob clockwise to raise the
frequency, counterclockwise to lower the frequency. Use
the knob together with the MENU button to switch the
mode setting. ( page 10 ~ 16)
!3 FM antenna terminals
(ANTENNA TERMINAL FM)
75 /ohms coaxial cables can be connected to these
terminals. For the connection procedure, see the section
“Connections”. ( page 6)
!4 AM antenna terminals
(ANTENNA TERMINAL AM)
Connect the included AM loop antenna. ( page 6)
Connect with this terminal when a medium wave outdoor
antenna is used.
!5 Analog output jacks
Connect these to the TUNER input terminals on the pre-
main amplifier. ( page 7)
!6 AC Inlet
Connect the included power supply cord here. ( page
7)
Whenever the unit is in the STANDBY state, the unit is still
connected to AC line voltage.
Please be sure to unplug the power supply cord when you
leave home for, say, a vacation.
Noise may be generated if a nearby television set is on
during the broadcasting reception. The tuner should be used
as far away from a television as possible.
The unit is also equipped with a back-up memory. This
function provides memory storage when the power switch
is off and with the power supply cord disconnected.
MEMO
Part names and functions
For details on the functions of these parts, refer to the pages given in parentheses ( ).
Front panel
Rear panel
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon TU-1500AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon TU-1500AE in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info