498787
12
Zoom out
Zoom in
Previous page
1/28
Next page
About the AV amplifier’s crossover frequency
selection
The crossover frequency of the satellite
speaker/center speaker and the active
subwoofer (the boundary between the
frequency range produced by the active
subwoofer and the other speakers) is set on the
connected AV amplifier, and is usually fixed at
between 80 and 120 kHz.
With some amplifiers, however, including the
Denon AV amplifier, this frequency can be
selected. When using this type of amplifier, the
crossover frequency can be selected to suit your
tastes.
When using the DSW-65 active subwoofer with
this type of amplifier, a richer sound can be
achieved by setting the crossover frequency to
around 150 Hz. Adjust the crossover frequency
to suit your tastes. For instructions on switching,
refer to your amplifier’s operating instructions.
When connecting to a Dolby Digital or dts-
compatible AV amplifier, whether one on which
the crossover frequency is fixed or one on which
it can be adjusted, we recommend setting the
LF DIRECT switch of the active subwoofer
(DSW-65) to the “ON” position.
n
Volume adjustment control (LEVEL)
This control only functions when the LF DIRECT
switch (v) is set to the “OFF” position.
Use this control to adjust the volume of the
active subwoofer.
When turned clockwise ( ) from the center
position, the volume of the active subwoofer
increases, and when turned counterclockwise
( ), the volume decreases. Set to the desired
position.
For some signals, a very soft sound will be
produced even when the volume adjustment
control(“LEVEL”) is turned fully counterclockwise
() and set to the minimum (“MIN”). This is not
a malfunction.
If this should happen, connect the cord
connected to the set’s LINE IN connector to an
output connector (SUB WOOFER PRE OUT,
MONO OUT, etc.) for which the signals pass
through the master volume circuitry of the AV
surround amplifier, etc., before being output.
Use the set’s volume adjustment control
(“LEVEL”) to adjust the volume difference with
the speakers other than the super woofer (front,
center, surround, etc.), and adjust the overall
volume using the master volume control on the
AV surround amplifier, etc.
m
Auto standby selector switch (AUTO STANDBY)
ON : The auto standby function is activated
OFF : The auto standby function is deactivated
,
Status indicator
The two-colored LED indicates the active
subwoofer’s operating status, as follows:
Power “ON”......................................Lights green
Auto power off (standby mode).............Lights red
Power “OFF” ............................................LED off
Protective circuit activated.................Flashing red
.
Power switch (POWER)
The power turns on when this switch is set to
the “ON” position.
Several seconds are required for the set to begin
operating. This is because the set includes a
built-in muting circuit to prevent noise when the
power switch is turned on and off.
When set to the “OFF” position, the power turns
off.
Auto Standby Function
The amplifier is automatically set to the
standby mode if no signal is input for 5 to 11
minutes, thereby saving electricity.
The power turns on immediately when a signal
is input.
PART NAMES AND FUNCTIONS (continued)
ENGLISH
12
1.SYS65L_ENG 04.6.19 11:58 AM ページ 12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon SYS-65HT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon SYS-65HT in the language / languages: German as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info