18664

Denon S101 Manual

19
Zoom out
Zoom in
Previous page
1/138
Next page
q Insert the included hexagonal wrench into the hole
at the side of the connector’s “+” side. (Arrow A)
w Turn the hexagonal wrench in the direction of
arrow B to loosen the cable.
e Pull out the old cable. Be careful not to leave any
broken wire parts inside the connector. (Arrow C)
r Peel off the cable’s sheath and insert the new
cable with the copper colored core wire twisted
tightly together into the connector. (Arrow D)
t Turn the hexagonal wrench in the direction of
Arrow E and tighten securely so that the cable cannot be pulled out. Be sure to connect both
sides of the cable to the connectors with the proper polarities.
If the polarities are inverted, the phase may be off and the bass sound may be missing, resulting
in an unnatural sound.
16
ENGLISH
ENGLISH
Connecting Other Sources Connecting Other Sources
COMPONENT VIDEO IN
Y
PB/CB
PR/CR
Monitor TV
D
F
• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” in “HELP” to comply with your TV’s video
format. When the TV is NTSC formatted set to NTSC.
• When the PROGRESSIVE/INTERLACED switch on the ADV-S101’s rear panel is set to
“PROGRESSIVE”, no video signals are output from the VIDEO OUT or S-VIDEO OUT terminals.
Set the PROGRESSIVE/INTERLACED switch on the ADV-S101’s rear panel to “INTERLACED”, if you
want to use the VIDEO OUT or S-VIDEO OUT signals. ( page 11, 15).
Connecting a component connections
(Better than S-Video picture quality)
• For the component output only, it is possible to switch between interlace image output and
progressive image output. It is not possible to specify progressive image output for the Video
output connectors or S-Video output connector.
PROGRESSIVE:
Select this when using the ADV-S101 connected to a progressive type TV.
INTERLACED:
Select this when using the ADV-S101 connected to an interlace type TV.
2 To switch from interlace to progressive
•Turn off the power before changing the switch.
• Choose settings according to the TV to be connected.
• Set the PROGRESSIVE/INTERLACED switch on the ADV-S101’s rear panel to
select the type of the TV.
To change the speaker cable
Connecting the antenna terminals
• An F-type FM antenna cable plug can be connected directly.
• If the FM antenna cable’s plug is not of the F-type, connect using the F-type antenna adapter
(Option).
Direction of
broadcasting station
75 Ω/ohms
COAXIAL cable
FM antenna
AM loop antenna
(Supplied)
AM outdoor
antenna
Ground
FM antenna
adapter
(Option)
C
D
Refer to the procedure below if you want to switch to a different speaker cable. This example
describes how to mount the “+” side cable to the connector. Mount the “–“ side cable in the same
way.
A
E
B
NOTE:
• Do not connect two FM antennas
simultaneously.
• Even if an external AM antenna is used, do
not disconnect the AM loop antenna.
• Make sure AM loop antenna lead terminals
do not touch metal parts of the panel.
PROGRESSIVE/INTERLACED
Black
White
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon S101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon S101 in the language / languages: English, Spanish as an attachment in your email.

The manual is 6,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info