159219
7
Zoom out
Zoom in
Previous page
1/32
Next page
7
w
Remote sensor
When operating the remote control unit,
point it at this sensor.
e
PHONES (headphones jack)
Plug the headphones into this jack.
No sound is produced from the speakers
when headphones are plugged in.
r
FUNCTION button
Use this to select the input (function).
The input changes in the following order
each time this button is pressed:
t
Display
Refer to page 8.
y
1
/
3
(play/pause) button
Press this button to start playing a disc.
When the disc tray is closed, playback
begins when this button is pressed.
When pressed in STANDBY mode, the
power automatically turns on and
playback begins (Auto On function).
Press this button again to stop playback
temporarily.
CD TUNER TAPE AUX
!0
MENU/ SET button
When pressed in the standby mode, the
standby mode is switched (the clock
display is switched on and off).
•When pressed while the clock is
displayed, the manual time setting mode
is set. (This cannot be set while the
clock is displayed in the standby mode.)
Switches the display of the timer setting
menu on and off.
When the function is set to FM and the
CT tuning mode is set, the mode
switches to the auto time setting mode.
When the function is set to TUNER and
an FM station is being received, if
pressed for more than 1 second, the
display switches to the AUTO PRESET
menu.
!1
8 /– , +/ 9 button
(8, 9 : CD automatic search
reverse/forward button
+ , – : TUNER up/down button)
Use the 8 and 9 buttons to move
to the beginning of a specific track while
in CD function.
Use the +/– button to select radio
stations while in TUNER function.
In TUNER function, press the 2 /BAND
and + buttons at the same time to
change the Preset mode, the 2 /BAND
and – buttons at the same time to
change the Tuning mode.
Use the +/– button when you adjust
tone control (BASS or TREBLE) and you
select menu function (display, time,
timer, or set up).
!2
5
(open/close) button
Press this button to open and close the
disc tray.
When pressed once, the disc tray opens
out, and when pressed again, the disc
tray closes. If a disc is loaded, the total
number of tracks and total playing time
of the disc are displayed several seconds
after the disc tray is closed.
When pressed in STANDBY mode, the
CD receiver’s power turns on.
!3
Disc tray
Load discs here.
q
Power operation switch (ON/STANDBY)
This turns the power for the entire
system on and off.
Press this once to turn the power on,
then press again to set the power to
STANDBY mode.
The LED color changes as follows,
according to the condition:
During power ON : green
During STANDBY : red
During TIMER STANDBY: orange
The muting mode is set when the main
unit’s power button is pressed and when
the standby mode is canceled from the
remote control unit. The power indicator
flashes green when in the muting mode,
then stops flashing and turns green once
the set is in the operational mode.
If the indicator is flashing orange
(quickly):
The protective circuit is activated.
If this happens, unplug the power cord
to turn the indicator off, then check the
input and output terminals on the rear
panel. Check in particular for short-
circuiting of the speaker cords. Once all
connections have been corrected, plug
the power cord. (Wait for at least 10
seconds after turning the power off
before turning it back on.)
Power is supplied to the RCD-
M35DAB/RCD-M33 even when the
power is in the standby mode (The clock
is displayed in the clock display mode.)
u
VOLUME control
Use this to adjust the overall volume
(Rotary Encorder System).
The volume increases when the control
is turned clockwise (,) and decreases
when it is turned counterclockwise (.).
The volume increases and decreases in
35 steps from the minimum (VOLUME
00) to the maximum (VOLUME MAX).
i
2 /BAND button
( 2 : CD stop button
BAND : TUNER band button)
In CD function, press this button to stop
playback.
•In TUNER function, use this button to
selecting the band.
For the RCD-M35DAB :
For the RCD-M33 :
o
SDB (Super Dynamic Bass)/TONE button
Press this button to select the preferred
sound of TONE CONTROL/SDB. Each
time this button is pressed, the display
changes as follows:
You can switch the SDB on/off by using
the +/– (up/down) button.
BASS and TREBLE can be adjusted by
using the +/– (up/down) button.
When you select S.DIRECT (Source
Direct), SDB/TONE is switched off, and
the sound characteristic becomes flat.
SDB can be controlled powerful bass
tones when listening at lower volume
levels.
FM AUTO FM MONO
AM
FM AUTO
FM MONO
AM
DAB
PART NAMES AND FUNCTIONS
6
(1) Front Panel
NOTE:
The SDB should be deactivated when
listening at higher volume levels.
Excessive bass at high volume levels
will result in a distorted sound and
may cause damage to your set and
speaker system.
NOTE:
Care must be taken when you adjust
the volume as the CD receiver is
equipped with an electronic volume
control. Turn the VOLUME control
slowly referring to the indication on
the display to adjust the volume.
q
w
e
r
ty
u
i
o
!0
!1
!2
!3
RCD-M33-EK 05.4.12 9:12 AM ページ 7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon rcd m 35 dab at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon rcd m 35 dab in the language / languages: English as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info