122765
26
Zoom out
Zoom in
Previous page
1/32
Next page
REMOTE CONTROL UNIT
RC-7000CI
OWNER’S MANUAL
IC Information (For Canadian customers)
1. DEVICE
RC-7000CI IC: 6963A-RC7000
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
APPAREIL
RC-7000CI IC: 6963A-RC7000
Cet appareil est conforme à la norme CNR-210 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux deux conditions
suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du
dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même
si ce brouillage est susceptible de compromettre le fonctionnement du
dispositif
FCC Information (For US customers)
1. DEVICE
RC-7000CI FCC ID: BV2-RC7000
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS DEVICE
This device, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modification not expressly approved by
DENON may void your authority, granted by the FCC, to use the device.
3. NOTE
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This device generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined
by turning the device OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Connect the device into an outlet on a circuit different from that to which the
receiver is connected.
Consult the local retailer authorized to distribute this type of device or an
experienced radio/TV technician for help.
IMPOTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not place near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
8. Only use attachments/accessories specified by the manufacturer.
9. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as liquid has been spilled the apparatus has been
exposed to rain or moisture, does not operate normally, or
has been dropped.
10. Batteries shall not be exposed to excessive heat such as sunshine, fire or the
like.
I
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused.
Please dispose of any materials in accordance with the local recycling
regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of
in accordance with the local regulations concerning battery disposal.
This product and the supplied accessories, excluding the batteries,
constitute the applicable product according to the WEEE directive.
HINWEIS ZUM RECYCLING:
Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann
wieder verwendet werden. Bitte entsorgen Sie alle Materialien entsprechend
der örtlichen Recycling-Vorschriften.
Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und
Bestimmungen.
Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden;
bitte entsorgen Sie die Batterien gemäß der örtlichen Vorschriften.
Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme
der Batterien!) entsprechen der WEEE-Direktive.
UNE REMARQUE CONCERNANT LE RECYCLAGE:
Les matériaux d’emballage de ce produit sont recyclables et peuvent être utilisés.
Veuillez disposer des matériaux conformément aux lois sur le recyclage en vigueur.
Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations
en vigueur.
Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut
conformément aux lois en vigueur sur la mise au rebut des piles.
Ce produit et les accessoires inclus, à l’exception des piles, sont des produits
conformes à la directive DEEE.
NOTA RELATIVA AL RICICLAGGIO:
I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili.
Smaltire i materiali conformemente alle normative locali sul riciclaggio.
Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore.
Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla
normativa locale sui rifiuti chimici.
Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla
direttiva RAEE, ad eccezione delle batterie.
ACERCA DEL RECICLAJE:
Los materiales de embalaje de este producto son reciclables y se pueden
volver a utilizar. Disponga de estos materiales siguiendo los reglamentos de
reciclaje de su localidad.
Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos
locales.
Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas
siguiendo los reglamentos de su localidad relacionados con los desperdicios
químicos.
Este producto junto con los accesorios empaquetados es el producto aplicable
a la directiva RAEE excepto pilas.
EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:
Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt
worden. Er wordt verzocht om zich van elk afvalmateriaal te ontdoen volgens
de plaatselijke voorschriften.
Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van
wit- en bruingoed op.
Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens
de plaatselijke voorschriften betreffende chemisch afval worden verwijderd.
Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de
richtlijn voor afgedankte elektrische en elektronische apparaten (WEEE) van
toepassing.
OBSERVERA ANGÅENDE ÅTERVINNING:
Produktens emballage är återvinningsbart och kan återanvändas. Kassera det
enligt lokala återvinningsbestämmelser.
När du kasserar enheten ska du göra det i överensstämmelse med lokala
regler och bestämmelser.
Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt
lokala bestämmelser för kemiskt avfall.
Denna apparat och de tillbehör som levereras med den uppfyller gällande
WEEE-direktiv, med undantag av batterierna.
II
DECLARACIÓN DE CONFORMIDAD
Por la presente, D&M Holdings Inc., Denon Brand Company, declara que
este RC-7000CI cumple con los requisitos esenciales y otras exigencias
relevantes de la Directiva 1999/5/EC, esta conforme con los siguientes
estandares:
EN300328, EN301489-01 y EN301489-17
Puede consultar a nuestro representante europeo, DENON EUROPE, acerca
de la declaración de conformidad.
EENVORMIGHEIDSVERKLARING
Hierbij verklaart D&M Holdings Inc., Denon Brand Company dat het toestel
RC-7000CI in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG, in overeenstemming is met de
volgende normen:
EN300328, EN301489-01 en EN301489-17
De eenvormigheidsverklaring mag worden geconsulteerd aan onze Europese
vertegenwoordiger, DENON EUROPA.
ÖVERENSSTÄMMELSESINTYG
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra
relevanta bestämmelser i Direktiv 1999/5/EC, uppfyller foljande standarder:
EN300328, EN301489-01 och EN301489-17
EU-konformitetsintyget kan på begäran fås från DENON EUROPE, vår
representant i Europa.
DECLARATION OF CONFORMITY
Hereby, D&M Holdings Inc., Denon Brand Company declares that this
product RC-7000CI is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC, in conformity with the
following standards;
EN300328, EN301489-01 and EN301489-17
The declaration of conformity may be consulted to our European
representative, DENON EUROPE.
ÜBEREINSTIMMUNGSERKLÄRUNG
Hiermit erklärt D&M Holdings Inc., Denon Brand Company, dass sich
das Gerät RC-7000CI in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet, den folgenden Standards entspricht:
EN300328, EN301489-01 und EN301489-17
Wenden Sie sich bei Fragen zur Konformitätserklärung an unseren
europäischen Vertreter, DENON EUROPE.
DECLARATION DE CONFORMITE
Par la présente, D&M Holdings Inc., Denon Brand Company déclare que
l’appareil RC-7000CI est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE, e conforme alle seguenti
normative:
EN300328, EN301489-01 et EN301489-17
La déclaration de conformité pourra être consultée auprès de notre
représentant en Europe, DENON EUROPE.
DICHIARAZIONE DI CONFORMITÀ
Con la presente D&M Holdings Inc., Denon Brand Company dichiara che
questo RC-7000CI è con-forme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE, e conforme alle seguenti
normative:
EN300328, EN301489-01 e EN301489-17
La dichiarazione di conformità può essere consultata presso il nostro
rappresentante europeo, DENON EUROPE.
QUESTO PRODOTTO E’ CONFORME
AL D.M. 28/08/95 N. 548
DENON EUROPE
Division of D&M Germany GmbH
An der Landwehr 19, Nettetal,
D-41334 Germany
III
Operation Network
function
Troubleshooting Specifications
PC
Application
Thank you for purchasing this DENON product. To ensure
proper operation, please read these owner’s manual carefully
before using the product.
After reading them, be sure to keep them for future
reference.
Getting Started
Accessories
Check that the following parts are supplied with the product.
Inserting the batteries
q Lift the clasp and remove
the rear lid.
w Load the four batteries
properly as indicated by
the marks in the battery
compartment.
e Put the rear cover back on.
NOTE
Use a LR03/AAA battery for the remote control unit.
If you try to operate the RC-7000CI / 7001RCI near the
device you want to operate but the device does not operate,
replace the batteries with new ones. (The included batteries
are only meant for verifying operation. Replace them with
new batteries soon.)
When inserting the batteries, be sure to do so in the proper
direction, following the “qand “wmarks in the battery
compartment.
To prevent damage or leakage of battery fluid:
Do
not use a new battery together with an old one.
Do
not use two different types of batteries.
Do
not attempt to charge dry batteries.
Do
not short-circuit, disassemble, heat or dispose of
batteries in flames.
If the battery fluid should leak, carefully wipe the fluid off the
inside of the battery compartment and insert new batteries.
Remove the batteries from the
remote control unit if it will
not be in use for long periods.
When replacing the batteries, have the new batteries ready
and insert them as quickly as possible.
“LOW BATTERY”appears on the LCD when the remaining
battery power decreases. When this happens, replace the
battery as soon as possible.
q Owners Manual .............................................................. 1
w Remote control ................................................................ 1
e LR03/AAA batteries ......................................................... 4
r CD-ROM .......................................................................... 1
t USB cable (Cord length: Approx. 3.3 ft / 1 m) .................. 1
Accessories ········································································ 1
Inserting the batteries ······················································
1
Operating range of the
remote control unit ··················· 2
Part names and functions ················································
2
Getting Started
Contents
Introduction ······································································· 3
Settings menu map ··························································
4
Operation the
LCD button ················································ 5
Settings
Setting the screen display time ·······································
5
Setting the
backlight on time ··········································· 6
Adjusting the
contrast ····················································· 6
Completing the setting ····················································
6
Various settings
Using the preset memory function ·································
7
Using the
learning function ·········································· 7, 8
Using the Macro function ············································
8, 9
Using the delay time function
·········································· 9
Using the
code search function ······································· 9
Favorites settings ····················································· 10, 11
Using the punch through function ··································
11
Editing pages ····························································11, 12
Editing devices ······················································ 12 ~ 15
Editing buttons ······················································ 15 ~ 18
Operation
Deleting signals registered with the learning function ···18
Deleting signals registered with the macro function ······
19
Deleting
favorites ···························································19
Deleting the registered punch-thru function ···················
19
Operational reset ···························································
20
User reset ······································································ 20
Lock function ································································· 21
Unlock function ······························································ 21
Network function ..................................................22
Operations using nodes
Adding nodes (1)···························································· 23
Adding nodes (2)···························································· 23
Deleting
nodes ······························································ 24
Viewing
nodes ······························································· 24
Changing
node labels ···················································· 25
Setting the receiver
display mode (RDM) ······················ 25
Checking the remote control unit version······················ 25
Troubleshooting .....................................................27
Specifications ..........................................................27
Getting Started
PC Application
RC-7000CI Editor function ·············································· 26
RC-7000CI Editor installation ········································· 26
Using RC-7000CI Editor ·················································
26
PC
Application
Operating range of the remote control
unit
Point the remote control unit at the remote sensor when
operating it.
30°
30°
Approx. 23 feet /
7 m
NOTE
The set may function improperly or the remote control unit
may not operate if the remote control sensor is exposed to
direct sunlight, strong artificial light from an inverter type
fluorescent lamp or infrared light.
For buttons not explained here, see the page indicated in parentheses ( ).
Part names and functions
o SETUP / MENU button ……………………………… (11)
Q0 Cursor buttons (uio p) ………………………… (11)
Q1 On-screen display button (OSD) …………………… (11)
Q2 Channel buttons (CH + –) …………………………… (11)
Q3 HDD 1/3 button ……………………………………… (11)
Q4 iPod 1/3 button ……………………………………… (11)
Q5 Tuning – / Search button (6) ………………… (7, 11)
Q6 Play button (1) ……………………………………… (7)
Q7 Skip button (8) …………………………………… (7)
Q8 REC button (4) ………………………………………… (11)
Q9 Pause button (3) …………………………………… (7, 11)
W0 Function / Number buttons ………………………(5 ~ 7)
W1 USB port
W2 Display …………………………………………………… (3)
W3 NEXT button …………………………………… (3, 5 ~ 7)
W4 Blue button
W5 Yellow button
W6 Surround parameter button (SURR) ……………… (11)
W7 Return button (RTN) ………………………………… (11)
W8 ENTER button ………………………………………… (11)
W9 Master volume control buttons (VOL + –) ………… (11)
E0 STATUS / HOME button ……………………………… (11)
E1 MUTE button …………………………………………… (11)
E2 EQ button ……………………………………………… (11)
E3 Tuning + / Search button (7) …………………… (7, 11)
E4 Skip button (9) …………………………………… (7, 11)
E5 Stop button (2) ……………………………………… (7, 11)
q POWER ON button
w Remote control signal transmitter
e POWER OFF button
r LCD buttons …………………………………… (3, 5 ~ 7)
t FUNCTION / DEVICE button ………………………… (6)
y BACK button …………………………………… (3, 5 ~ 7)
u Red button
i Green button
Getting Started Operation Network
function
Troubleshooting Specifications
q
w
e
r r
W3
W2
W4
W5
W6
W7
W8
W9
E0
E1
E3
E5
E2
E4
y
u
i
o
Q0
Q1
Q2
Q4
Q3
Q5
Q7
Q6
Q8
Q9
W0
W1
t
For instructions on using with RF connections, refer to the
operating instructions of the RC-7001RCI (sold separately).
About USB ports
When editing the RC-7000CI’s functions using the exclusive
“RC-7000CI Editor” application software, connect the included
USB cable (vpage 26).
Getting Started Network
function
Troubleshooting Specifications
PC
Application
Operation
LCD button
1
To use to operate an AV amplier (AV
receiver), press [Denon1].
b [Denon2] is a function for system expansion in the future.
Normally select [Denon1].
2
Press [YES].
3
Press NEXT.
After “PLEASE WAIT” is displayed, the default device
is set to [Denon1].
4
Press DEVICE.
The initial settings screen appears.
Introduction
Operation of the LCD buttons
When buttons on the remote control unit are pressed, various
settings and operation items appear on the LCD screen.
LCD button
When batteries are loaded for the first time
Make the setting described below.
Initial display screen
The initial display settings are shown on the display below.
When using the RF two-way communication
function
Change the amplifier setting to “RF” at “Setting the remote
control code transmission mode (In the case of RF)“ (vpage
15).
n Operation for selecting
Press the LCD button to the left or right of the displayed
item name to select it.
The screen is displayed for 5 seconds. Operate while the
screen is displayed. (“Setting the screen display time
(vpage 5))
When “
PAGE” is displayed at the bottom of the screen,
there are one or more other pages in addition to the one
currently displayed. Use the NEXT and BACK button to
switch screens.
BACK button
n Indication of item names in this manual
In this manual, the names of items displayed on the screen
are indicated [ ]. (Example: [Denon1])
GScreen 1H GScreen 2H
DEVICE SELECT
AMP ZONE2
ZONE3 ZONE4
TUNER CD
DVD TV
SAT
Cable
Page 1/2
DEVICE SELECT
VCR 1 iPod
VCR 2 NetAud
DTU
Page 2/2
Operation
NEXT button
DEVICE button
NOTE
A DENON product compatible with the RC-7001RCI (sold
separately) is required to use this function.
When the LCD screen in the display on screen 1 goes off,
press the RC SETUP button for 3 seconds to resume the original
screen.
Please select
which type of
Denon product
you are using
below.
Denon 1 Denon 2
1
You have selected
Denon 1
Are you
sure you
want to set up
Denon1?
NO YES
2
This process
will take a few
moments to
complete. Press
NEXT to begin
Setting up your
Denon1 remote.
PLEASE WAIT
3
Denon1 has been set
succesfully!
Press NEXT to
continue with
more setup
choices or DEVICE
to begin using
your remote.
4
Initial setting
TV Hitachi
SAT RCA
Cable Motrola
VCR-1 Hitachi
VCR-2 SONY
Others DENON
Getting Started Network
function
Troubleshooting Specifications
PC
Application
Settings menu map
Operation
n BASIC SETUP
(vpage 7, 9)
BRAND SET
CODE SEARCH
n FAVORITES
(vpage 10, 19)
ADD / REDO
DELETE
CONFIGURE
· FAV DEVICE
· FAV IR DELAY
· TOTAL DIGITS
· CHANNEL KEY
n MACROS
(vpage 8, 9, 19)
ADD / REDO
DELETE
EDIT DELAY
n PUNCH THRU
(vpage 11, 19)
ADD
· CHANNEL TUNE
· TRANSPORTS
· VOLUME CONT.
· MENU NAVIG.
CLEAR
· CHANNEL TUNE
· TRANSPORTS
· VOLUME CONT.
· MENU NAVIG.
n LEARNING
(vpage 7, 18)
LEARN KEY
ERASE LEARN
n EDIT PAGE
(vpage 11, 12)
ADD PAGE
DELETE PAGE
n EDIT DEVICE
(vpage 11, 13)
MOVE/SWAP
MOVE/INSERT
COPY
ERASE
DISPLAY MODE
IR/RF
n EDIT TEXT
(vpage 15, 18)
DEVICE NAME
KEY NAME
n EDIT FUNC
(vpage 15, 16, 17)
MOVE/SWAP
MOVE/INSERT
COPY
ERASE
DISPLAY MODE
ADD FUNC
ADD Synth b
b This is a function for system expansion in the future.
n RESET/LOCK
(vpage 20, 21)
OP RESET
USER RESET
LOCK
UNLOCK
n NETWORK
(vpage 23, 24)
ADD NODES
DELETE NODES
VIEW NODES
EDIT LABEL
n USER PREF
(vpage 5, 6, 25
)
VERSION INFO
CONTRAST
DISPLAY T/O
LIGHT T/O
RDM
Getting Started Network
function
Troubleshooting Specifications
PC
Application
NEXT
BACK
DEVICE
RC SETUP
LCDタン
LCDタン
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Settings
Setting the screen display time
Use this procedure to set the time until the screen
display turns off.
Initial setting: 5 seconds
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [USER
PREF].
3
Press [DISPLAY T/O].
4
Press NEXT.
5
Press [–DISPLAY T/O+] to set the time until
the light turns off.
LCD button on right side ...................................... +
LCD button on left side ........................................
b
The time can be set between 1 (MIN) and 30 (MAX).
6
Press [SAVE].
7
Press NEXT.
Operation the LCD button
1
Press DEVICE.
The “DEVICE SELECT” menu is displayed.
2
Press the LCD button for the device
(equipment) you want to operate.
b If there are multiple pages, use the NEXT and BACK
button to switch screens.
3
Press the LCD button for the item you want
to operate.
b If there are multiple pages, use NEXT and BACK to switch
screens.
Operation
LCD buttonLCD button
Getting Started Network
function
Troubleshooting Specifications
PC
Application
NEXT
VOL+ –
7
1
9
2
BACK
RC SETUP
6
8
DEVICE
LCDタン
LCDタン
3
Adjusting the contrast
Set this if the characters on the screen are hard to see.
Initial setting: Level 5
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [USER
PREF].
3
Press [CONTRAST].
4
Press NEXT.
5
Press [–CONTRAST+] to set the contrast.
LCD button on right side .......................................+
LCD button on left side .........................................
b The contrast can be set within the range of “Level 0
(MIN)” to “Level 12 (MAX)”.
6
Press [SAVE].
7
Press NEXT.
Setting the backlight on time
Use this procedure to set the time until the backlight
turns off.
Initial setting: 5 seconds
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [USER
PREF].
3
Press [LIGHT T/O].
4
Press NEXT.
5
Press [–LIGHT T/O+] to set the time until
the light turns off.
LCD button on right side .......................................+
LCD button on left side .........................................
b The time can be set between Light Off and 30 (MAX).
6
Press [SAVE].
7
Press NEXT.
Completing the setting
Press DEVICE until the “DEVICE SELECT”
screen appears.
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications
PC
Application
8
Use 1, 2, 3, 6, 7, 8, 9,
VOL+ to check whether the device to be
added operates.
Operates ........................................ [YES]
The IR/RF selection screen appears.
Does not operate ........................... [NO]
The screen switches to the next code. Find the code
that operates and set it by pressing [YES].
9
Press [IR] or [RF] to select the remote control
signal.
[IR] :
Infrared signals are transmitted.
[RF] :
Send RF signals to the RC-7001RCI remote control receiver
(sold separately).
b For details on the RC-7001RCI (sold separately), see
“Network function” (vpage 22).
10
At the “Select Position” screen, press the
LCD button for the posision at which you
want to add the preset device.
The setting is entered.
b Press [NO] to end, [YES] to continue.
NOTE
Depending on the product’s year of manufacture and
differences in functions from model to model, there may be
some buttons that do not operate or buttons that operate
erroneously.
Using the learning function
This function lets you register the desired remote
signals of devices by sending them to the remote
control unit.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [LEARNING].
3
Press [LEARN KEY].
4
Press NEXT twice.
5
At the “Select Device” screen, press the LCD
button for the device whose remote control
signals you want to register.
6
At the “Learn Key” screen, press the LCD
button for the operation button name you
want to register.
b Signals can be “learned” at buttons other than RC SETUP,
NEXT, BACK and DEVICE.
Various settings
Using the preset memory function
The remote control unit can be preset to operate devices
of various brands.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [BASIC SETUP].
3
Press [BRAND SET].
4
Press NEXT.
5
At the “Press Device Type” screen, press
the LCD button for the device you want to
set in the preset memory.
6
Press NEXT.
7
At the “Select Brand” screen, press the LCD
button for the device’s brand name.
b If the brand you want to choose is not displayed, press
NEXT to switch the brand display.
b If there are multiple codes, “1 of
z
” is displayed.
(
z
is the number of codes)
Operation
Getting Started Network
function
Troubleshooting Specifications
PC
Application
NEXTBACK
DEVICE
RC SETUP
LCDタン
LCDタン
Using the Macro function
This function allows you to register a series of
operations at a single button.
With this function you can for example turn on the
amplifier, select the input source, turn on the TV’s
power, turn on the source device’s (equipment) power
and set the play mode all by pressing a single button.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [MACROS].
3
Press [ADD/REDO].
4
Press NEXT twice.
5
At the “Assign Macro” screen, press the
LCD button for the device (equipment) for
which you want to register the macro.
6
Press the button at which you want to
register the macro.
b Macros can be registered at buttons other than NEXT,
BACK and DEVICE.
7
Press NEXT to register the next signal.
b Press DEVICE to select the device.
b Repeat steps 5 to 6.
7
Place the remote control units with their
signal transmitters facing each other, press
NEXT, then immediately press the button
on the remote control unit you want to
register.
”Success!” is displayed if the
code was learned successfully.
8
To register other buttons, press NEXT.
b Repeat steps 6 to 8.
9
Press [EXIT] to exit the learning mode.
b Press [EDIT] if you want to change the button name.
Perform the procedure at Changing the button name
(v page 18) starting from step 7.
NOTE
The learning function may not work for some remote control
units, and sometimes a device may not operate properly even
if its remote control signals have been learned. In this case,
use the remote control unit included with the device.
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications
PC
Application
Using the code search function
This function lets you search for preset codes when
adding new devices (equipment) to the remote control
unit.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [BASIC SETUP].
3
Press [CODE SEARCH].
4
Press NEXT.
5
At the “Press Device Type” screen, press
the LCD button for the device (equipment)
whose code you want to search for.
6
Press NEXT twice.
7
If the device (equipment) operates when the
remote control unit’s buttons are pressed,
press [YES].
b If [NO] is pressed, the code switches. Press a remote
control unit button again to check. Press [BACK] to return
to the previous code.
8
At the “Select Position” screen, press the
LCD button for the position at which you
want to add the preset device (equipment).
b Press [NO] to end, [YES] to continue.
8
Press RC SETUP.
The registration menu is displayed.
9
Press [SAVE] to register the set macro.
[TEST] :
Press this to send the registered macro to check it.
[– DELAY +] :
Use these to set the transmission interval. This can be set
to between “0.05(MIN)” and “60(MAX)”. (Initial setting: 0.25
seconds)
[CANCEL ENTRY] :
Press this to cancel the
last code registered and return to
the registration mode.
[START OVER] :
Press this to
start over from the beginning.
10
Press [EXIT] to end the setting.
b Press [EDIT] if you want to change the button name
(macro name).
Perform the procedure at Changing the button name
(vpage 18) starting from step 7.
Using the delay time function
The interval at which the remote control signals
registered with the system call function are sent (the
“delay time”) can be set.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [MACROS].
3
Press [EDIT DELAY].
4
Press NEXT twice.
5
The “Edit Macro” screen is displayed.
Select a macro that has been registered.
6
Press NEXT.
7
Use [– DELAY +] to change the delay time,
then press [SAVE].
[TEST] :
Press this to send the registered macro to check it.
[– DELAY +] :
Use these to set the transmission interval.
[CREATE AGAIN] :
The macro registration screen reappears.
8
Press [EXIT] to end the setting.
Operation
NOTE
The macro setting button cannot be registered in a macro.
Getting Started Network
function
Troubleshooting Specifications
0
PC
Application
NEXT
ENTER
RC SETUP
LCDタン
LCDタン
Registering favorites
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [FAVORITES].
3
Press [ADD/REDO].
4
Press NEXT.
5
Press [KEY].
b When [PAGE] is selected, pages can be added to [MAIN]
or [DEVICE].
When [PAGE] is selected, press [MAIN] or [DEVICE].
When [MAIN] is selected, press [YES] to set.
When [DEVICE] is selected, select the device (equipment)
for which a page is to be added.
6
Press NEXT.
7
At the “Assign Favorite” screen, select the
button for the place to be stored in the
favorites.
Favorites settings
Favorites settings
Use this function to register your favorite channel
numbers so they can be operated with a single button.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [FAVORITES].
3
Press [CONFIGURE].
4
Press NEXT twice.
5
At the “CONFIGURE FAV” screen, press
the LCD button for the item you want to
set.
[FAV DEVICE] :
Press this to select the device to be stored in the favorites.
This is initially set to “SAT”.
[FAV IR DELAY] :
Press this to set the interval at which the
remote control
signals are sent when buttons at which favorites have been
registered are pressed.
[TOTAL DIGITS] :
Use this to set the number of digits of channels registered
in the favorites.
[CHANNEL KEY] :
Set this to add ENTER after registered favorites
(Set this for types of devices for which ENTER is pressed to
set the channel after selecting it with the number buttons.)
To add ENTER at the end of the channel, press ENTER. If you
do not want to add ENTER, press NEXT.
b When [EXIT] is pressed, the setting is completed. Press
[CONFIG] to continue registering.
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications

PC
Application
Inserting pages
Editing pages
Pages can be inserted and devices (equipment) or
buttons can be added in the device (equipment) select
menu or in the individual devices.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT PAGE].
3
Press [ADD PAGE].
4
Press NEXT.
5
Press [MAIN] to add a page to the device
select menu, [DEVICE] to add a page in the
device (equipment).
b When and only when [DEVICE] is selected, press the LCD
button for the device to which you want to add a page.
6
Press [YES].
The page is added.
b Press NEXT to return to the setting menu.
8
Input the number (channel) you want to
register.
9
Press NEXT.
10
Press [SAVE] to register the favorite.
b Press [EDIT] if you want to change the button name.
11
Press [EXIT] to end the registration.
Press [ADD] to continue registering.
Using the punch through function
Even when a different device mode is selected, it is
possible to assign the buttons below to a different device
in units of groups.
For example, the DVD play operation can be performed
even if the operating mode is set to the amplifier.
1
Press RC SETUP for 3 seconds.
The“PROGRAM DEVICE” menu is displayed.
2
Press [PUNCH THRU].
3
Press [ADD].
4
Press NEXT.
5
At the Punch Thru” screen, press the LCD
button for the group you want to set.
The functions for which punch thru can be assigned in
units of groups are as shown on the table below.
Groups Functions
CHANNEL TUNE CH+, CH–, STATUS, 1~9,
0/10, +10
TRANSPORTS
iPod 1/3,
HDD 1/3, EQ, 6, 7,
8, 9, REC, 3, STOP,
VOLUME
CONTROL
VOL+, VOL–, MUTE
MENU
NAVIGATION
SETUP, SURR, OSD, RTN,
uiop, ENTER
6
Press NEXT.
7
At the “Source Device” screen, press the
LCD button for the device of the group you
want to set.
8
Press NEXT.
9
At the “Target Device” screen, press the
LCD button or the device whose group
selected at step 7 you want to send.
10
Press [YES].
b Press NEXT to return to the setting menu.
Operation
Getting Started Network
function
Troubleshooting Specifications

PC
Application
NEXTBACK
RC SETUP
LCDタン
LCDタン
Moving or swapping devices
Editing devices
Devices registered in the remote control unit can be
moved, copied and inserted.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press [MOVE/SWAP].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device (equipment) you
want to move.
6
Press NEXT.
7
At the “Target Device” screen, press the
LCD button for the target destination or the
device (equipment) to be substituted.
8
Press [YES].
The device is moved.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT PAGE].
3
Press [DELETE PAGE].
4
Press NEXT.
5
Press [MAIN] to delete a page from the
device select menu, [DEVICE] to delete a
device (equipment) page.
6
Select the page to be deleted using NEXT
and BACK, then press [SELECT PAGE].
7
Press [YES].
The page is delete.
b Press NEXT to return to the setting menu.
Deleting pages
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications

PC
Application
Copying devices
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press [COPY].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device (equipment) you
want to copy.
6
Press NEXT.
7
At the “Target Device” screen, press the
LCD button for the place you want to copy.
The device at the copy destination is cleared and the
device is copied.
8
Press [YES].
The device is moved.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Deleting devices
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press [ERASE].
4
Press NEXT.
5
At the “Select Device” screen, press the LCD
button for the device you want to delete.
6
Press [LEAVE EMPYT] or [SHIFT ALL UP].
[LEAVE EMPTY] :
The device (equipment) is deleted.
[SHIFT ALL UP] :
The device is deleted and the other devices are all shifted
up, filling in the space of the deleted device.
7
Press [YES].
The device is deleted.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Inserting devices
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press [MOVE/INSERT].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device you want to
move.
6
Press NEXT.
7
At the “Target Device” screen, press the
LCD button in the place you want to insert.
8
Press [YES].
The device is moved.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Operation
Getting Started Network
function
Troubleshooting Specifications

PC
Application
NEXT
RC SETUP
LCDタン
LCDタン
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press NEXT.
4
Press [IR/RF].
5
Press NEXT.
6
At the “Select Device” screen, press the LCD
button for the device whose transmission
mode you want to change.
7
Press NEXT.
8
Press [IR].
[IR] :
The codes are sent as infrared signals.
9
Press [YES].
The transmission mode is set.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press [DISPLAY MODE].
4
Press NEXT.
5
At the “Select Device” screen, press the LCD
button for the device whose display mode
you want to change.
6
Press [COLUMN MODE] or [ROW MODE].
[COLUMN MODE] :
The devices are displayed two per row.
[ROW MODE] :
The devices are displayed one per row.
7
Press [YES].
The display mode is set.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Setting the device display mode
Use this procedure to select the way in which the devices
(equipment) are displayed.
Setting the remote control code transmission
mode (In the case of IR)
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
NOTE
The display mode is not set in the device. Set with respect to
the LCD button position.
Getting Started Network
function
Troubleshooting Specifications

PC
Application
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press [MOVE/SWAP].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device of the button you
want to move.
6
At the “Select Key” screen, press the LCD
button of the button you want to move.
7
Press NEXT.
8
At the “Target Device” screen, press the
LCD button of the device for the destination
or the button to be swapped.
9
At the “Select key” screen, press the LCD
button for the destination or the button to
be swapped.
10
Press [YES].
The button moves or is replaced.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Editing buttons
Use this procedure to move, copy and insert buttons.
Moving or swapping buttons
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT TEXT].
3
Press [DEVICE NAME].
4
At the “Select Device” screen, press the LCD
button for the device (equipment) whose
name you want to change.
5
Press NEXT.
6
At the “Edit Text” screen, use the rst
column of LCD buttons to select the position
of the character to be edited.
7
Select the character to be input with the
second column of LCD buttons, then press
[SELECT].
b Lower case letters are input when [CAPS] is displayed,
capital letters when [lower] is displayed.
Up to 12 characters can be input.
8
Press [SAVE].
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Changing the device name
Operation
Setting the remote control code transmission
mode (In the case of RF)
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT DEVICE].
3
Press NEXT.
4
Press [IR/RF].
5
Press NEXT.
6
At the “Select Device” screen, press the LCD
button for the device whose transmission
mode you want to change.
7
Press NEXT.
8
Press [RF], then press [YES].
[RF] :
The codes are sent as radio waves.
b The setting at Adding nodes” (vpage 23) must be
made in order to add [RF].
9
Press NEXT.
b When [RF] is selected, the RC-7001RCI (sold separately)
node number is displayed. Press LCD button.
10
Press [YES].
The transmission mode is set.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Getting Started Network
function
Troubleshooting Specifications

PC
Application
NEXT
RC SETUP
LCDタン
LCDタン
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press [COPY].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device (equipment) of
the button you want to copy.
6
At the “Select key” screen, press the LCD
button for the button you want to copy.
7
Press NEXT.
8
At the “Target Device” screen, press the
LCD button of the device to copy to.
9
At the “Select Key” screen, press the LCD
button for copy destination.
10
Press [YES].
The button is copied.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Copying buttons
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press [MOVE/INSERT].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device of the button you
want to move.
6
At the “Select key” screen, press the LCD
button for the button you want to move.
7
Press NEXT.
8
At the “Target Device” screen, press the
LCD button for the device of the button for
the place to be inserted.
9
At the “Select key” screen, press the LCD
button for insert destination.
10
Press [YES].
The button is inserted.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Inserting buttons
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications

PC
Application
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press NEXT, then press [ADD FUNC].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device (equipment) you
want to add.
6
Press NEXT.
7
At the “ADD IR” screen, press the LCD
button for the function of the button you
want to add.
8
Press NEXT.
9
At the “Select key” screen, press the LCD
button for the position of the button you
want to add.
10
Press [TEST KEY], and if the operation has
been performed press [YES].
b Press [YES] to add more buttons.
Adding buttons
When new buttons are added, it is possible to select and add
new functions.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press [DISPLAY MODE].
4
Press NEXT.
5
At the “Select Device” screen, press the LCD
button for the device of the button whose
display mode you want to change.
6
At the “Select key” screen, press the LCD
button for the button whose display mode
you want to change.
7
Press [COLUMN MODE] or [ROW MODE].
[COLUMN MODE] :
The buttons are displayed two per row.
[ROW MODE] :
The buttons are displayed one per row.
8
Press [YES].
The display mode is set.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Setting the button display mode
Use this procedure to select the way in which the buttons are
displayed.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT FUNC].
3
Press [ERASE].
4
Press NEXT.
5
At the “Source Device” screen, press the
LCD button for the device of the button you
want to delete.
6
At the “Select key” screen, press the LCD
button for the button you want to delete.
7
Press [LEAVE EMPYT] or [SHIFT ALL UP].
[LEAVE EMPTY] :
The button is deleted.
[SHIFT ALL UP] :
The button is deleted and the other buttons are all shifted up,
filling in the space of the deleted button.
8
Press [YES].
The button is deleted.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Deleting buttons
Operation
Getting Started Network
function
Troubleshooting Specifications

PC
Application
NEXT
RC SETUP
LCDタン
LCDタン
Deleting signals registered with the
learning function
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [LEARNING].
3
Press [ERASE LEARN].
4
Press NEXT twice.
5
At the “Source Device” screen, press the
LCD button for the device you want to
delete.
6
At the “Select Key” screen, press the button
for the learning function you want to erase.
7
To delete, press [YES].
If you do not want to delete, press [NO].
b Press [NO] to end, [YES] to continue.
Changing the button name
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [EDIT TEXT].
3
Press [KEY NAME].
4
At the “Select Device” screen, press the LCD
button for the device whose button name
you want to change.
5
At the “Select key” screen, select the LCD
button for the button whose button name
you want to change.
6
Press NEXT.
7
At the “Edit Text” screen, use the rst
column of LCD buttons to select the position
of the character to be edited.
8
Select the character to be input with the
second column of LCD buttons, then press
[SELECT].
b Lower case letters are input when [CAPS] is displayed,
capital letters when [lower] is displayed.
Up to 12 characters can be input.
9
Press [SAVE].
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting Specifications

PC
Application
Deleting favorites
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [FAVORITES].
3
Press [DELETE].
4
Press NEXT twice.
5
At the “Source Device” screen, press the
LCD button for the device (equipment) you
want to delete.
6
At the “Select key” screen, press the LCD
button for the button you want to delete.
7
To delete, press [YES].
If you do not want to delete, press [NO].
b Press [NO] to end, [YES] to continue.
Deleting the registered punch-thru
function
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [PUNCH THRU].
3
Press [CLEAR].
4
Press NEXT.
5
At the Punch Thru” screen, press the LCD
button for the group you want to delete.
6
Press NEXT.
7
At the “Select Device” screen, press the LCD
button for the device (equipment) whose
punch through setting you want to delete.
8
To delete, press [YES].
If you do not want to delete, press [NO].
b Press NEXT to return to the settings menu.
Deleting signals registered with the
macro function
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press [MACROS].
3
Press [DELETE].
4
Press NEXT twice.
5
At the “Source Device” screen, press the
LCD button for the device (equipment)
whose macro you want to delete.
6
At the “Select Key” screen, press the LCD
button for the macro you want to delete.
7
To delete, press [YES].
If you do not want to delete, press [NO].
b Press [NO] to end, [YES] to continue.
Operation
Getting Started Network
function
Troubleshooting Specifications
0
PC
Application
NEXT
RC SETUP
LCDタン
LCDタン
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [RESET/LOCK].
3
Press [USER RESET].
4
Press NEXT.
5
Press [YES].
6
Press NEXT.
“PLEASE WAIT” is displayed and the setting is reset.
7
Press NEXT.
The settings menu reappears.
User reset
This procedure deletes the macro settings added by
the user and the remote control codes that have been
learned. It does not delete added devices.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [RESET/LOCK].
3
Press [OP RESET].
4
Press NEXT.
5
Press [YES].
6
Press NEXT.
“PLEASE WAIT” is displayed.
7
Press NEXT.
The settings are returned to as they were upon purchase
(vpage 3).
Operational reset
The settings are returned to as they were upon
purchase.
Operation
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Getting Started Network
function
Troubleshooting SpecificationsPC
Application
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [RESET/LOCK].
3
Press [LOCK].
4
Press NEXT twice.
5
At the “Select Device” screen, press the LCD
button for the device (equipment) you want
to lock.
6
Press [YES].
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT, then press [RESET/LOCK].
3
Press [UNLOCK].
4
Press NEXT twice.
5
At the “Select Device” screen, press the LCD
button for the device (equipment) you want
to unlock
6
Press [YES].
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Operation
Lock function
When locked, device (equipment) editing is not
possible.
Unlock function
This procedure unlocks devices (equipment) that have
been locked.

Getting Started Operation Troubleshooting Specifications

PC
Application
This functions uses the RC-7001RCI (sold separately).
When a wireless (RF) network is established using the RC-7001RCI (sold separately), the RC-7001RCI is called a node. An
individual node number is registered for each RC-7001RCI unit. When registering devices with the RC-7001RCI, once the RF
transmission settings are made, when a button on a device for which the node number is set is pressed, the remote control
signals are sent (wireless) and received by the RC-7001RCI corresponding to the node number of the transmission target.
Monitor
Monitor
Monitor
AV amplifier
DVD player
AV amplifier
DVD player
FLFR
FLFR
Repeater 1
(RC-7001RCI, sold
separately)
Repeater 2
(RC-7001RCI,
sold separately)
Remote control
(RC-7000CI)
: RF (Two-way communications)
: IR (Infrared communications)
Network function
NOTE
Using the wireless function near microwave ovens, devices
using a wireless LAN, cordless telephones, Bluetooth
devices or other wireless devices could adversely affect
communications performance. In this case move away from
the interfering device.
If the RC-7000C1 cannot properly receive radio signals due
to excessive distance between it and the RC-7001RC1 (sold
separately), radio interference, etc., “RF OUT OF RANGE”is
displayed on the LCD screen.
Network
function
Getting Started Operation Troubleshooting Specifications

PC
Application
NEXT
RC SETUP
LCDタン
LCDタン
Operations using nodes
Adding nodes (1)
Use this procedure to register a node number and add an
RC-7001RCI (sold separately) to the network.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [NETWORK].
3
Press [ADD NODES].
4
Press NEXT.
5
To add the remote control unit to the
network, press [REMOTE].
6
Press RESET/CONFIG on the RC-7001RCI
(sold separately) for about 1 second.
The indicator flashes green.
7
Press NEXT twice.
“Success!” is displayed when the device has been
added successfully.
b Press NEXT to return to the settings menu.
Network
function
LCD buttonLCD button
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Adding nodes (2)
Use this procedure to add a second or more units of the
RC-70001CI (sold separately) to the network.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [NETWORK].
3
Press [ADD NODES].
4
Press NEXT.
5
To add the RC-7001RCI to the network,
press [OTHER].
6
Press RESET/CONFIG on the RC-7001RCI
(sold separately) for about 1 second.
The indicator flashes red.
7
Press NEXT twice.
“Success!” is displayed when the device has been
added successfully.
b Press NEXT to return to the settings menu.
Press RESET/CONFIG on the RC-7001RCI (sold separately) for at
least 10 seconds so that the indicator lights red.
Getting Started Operation Troubleshooting Specifications

PC
Application
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [NETWORK].
3
Press [VIEW NODES].
4
Press NEXT twice.
The node numbers of the RC-7001RCIs (sold separately)
registered on the network are indicated with an
z
mark
after them.
b Press NEXT twice to return to the settings menu.
Viewing nodes
Use this procedure to search for and display a list of RC-
7001RCIs (sold separately) registered in the network.
NEXT
RC SETUP
LCDタン
LCDタン
About the button names in these explanations
[ ] : LCD buttons for selection items
Button name only:
Indicates a button on the remote control unit
Network
function
LCD buttonLCD button
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [NETWORK].
3
Press [DELETE NODES].
4
Press NEXT twice.
The RC-7001RCI’s (sold separately) node number is
displayed.
5
Select the node number to be deleted, then
press [YES].
6
Press NEXT.
b Press [NO] to end, [YES] to continue.
Deleting nodes
Use this procedure to delete RC-7001RCI (sold
separately) units by specifying the node number from
the current network.
Getting Started Operation Troubleshooting Specifications

PC
Application
Setting the receiver display mode
(RDM)
This setting is made for conducting two-way
communications between the RC-7001RCI (sold
separately) and compatible DENON products. The status
information of the compatible DENON product can be
displayed on the set's screen. Use this procedure to set
the RDM page display position.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [USER
PREF].
3
Press [RDM].
4
Press NEXT.
5
Press [YES].
6
Use [FIRST] and [LAST] to set the position
at which you want the RDM page to be
displayed.
[FIRST] :
The RDM page is displayed at the beginning of the normal
button screen.
[LAST] :
The RDM page is displayed at the end.
b Press NEXT to return to the settings menu.
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [USER
PREF].
3
Press [VERSION INFO].
The LCD button version information is displayed.
b Press NEXT twice to return to the settings menu.
Checking the remote control unit version
Network
function
1
Press RC SETUP for 3 seconds.
The “PROGRAM DEVICE” menu is displayed.
2
Press NEXT twice, then press [NETWORK].
3
Press [EDIT LABEL].
4
Press NEXT twice.
The RC-7001RCI’s (sold separately) node number is
displayed.
5
Select the node number to be changed, then
press NEXT.
The edit screen for the selected node appears.
6
At the “Edit Text” screen, use the rst
column of LCD buttons to select the position
of the character to be edited.
7
Select the character to be input with the
second column of LCD buttons, then press
[SELECT].
b Lower case letters are input when [CAPS] is displayed,
capital letters when [lower] is displayed.
8
Press [SAVE].
9
Press NEXT.
b When [NO] is pressed, the setting menu reappears. To
continue, press [YES].
Changing node labels
Use this procedure to add labels to RC-7001RCIs (sold
separately) for easier distinction.
Getting Started Operation Network
function
Troubleshooting Specifications

NOTE
During data upload or download using “RC-7000CI Editor”
do not carry out the following operations. Failure of the main
unit and personal computer may result.
Remove the USB cable.
Switch off the personal computer power.
Remove batteries from main unit.
First connect the RC-7000CI to the personal computer using
the USB cable provided.
Use a computer connected to the Internet.
1
Load the CD-ROM (RC-7000CI Editor) in
the CD-ROM drive.
2
Run “RC-7000CI Editor.exe”
b Follow the installation instructions on the installation
wizard screen.
b After installation, the “Installation complete dialog
message is displayed.
3
Press “Finish” to nish installation, and
start the application.
1
When using the application for the rst
time, check the New User box, enter e-mail
address, password, etc., and press OK.
2
Run “RC-7000CI Editor.exe” from the CD-
ROM drive in My Computer.
“RC-7000CI Editor” starts up.
3
Follow the wizard instructions.
PC Application
RC-7000CI Editor function
n You can use “RC-7000CI Editor” for the
following operations.
Editing RC-7000CI setting data.
Backing up RC-7000CI setting data on the PC.
Remote control code database downloading.
n Recommended devices and environment
required for using “RC-7000CI Editor”.
Personal computer running Windows
®
XP Service Pack2
operating system.
HDD with sufficient free disk space.
USB 2.0 connection terminal.
Internet connection environment
RC-7000CI Editor installation Using RC-7000CI Editor
PC
Application
Getting Started Operation Network
function
PC
Application
Troubleshooting
1. If a problem should arise, first check the following:
2. Is the set being operated as described in the operating instructions ?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a
malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
Symptom Cause Countermeasure Page
Set does not work
properly when remote
control unit operated.
Batteries are worn.
You are operating outside of the specified
range.
Obstacle between
main unit and remote
control unit.
The batteries are
not inserted in the proper
direction, as indicated by the polarity
marks in the battery compartment.
The set’s
remote control sensor is
exposed to strong light (direct sunlight,
inverter type fluorescent bulb light, etc.).
Replace with new batteries.
Operate within the specified range.
Remove the obstacle.
Insert the batteries in the proper d
irection,
following the polarity marks in the battery
compartment.
Move the set to a place in which the
remote control sensor will not be exposed
to strong light.
1
2
2
2
2
Display screen does
not appear.
Brightness setting is inappropriate. Adjust the screens brightness at
Adjusting the contrast”.
6
Wireless connections
with the RC-
7001RCI (sold
separately) cannot be
established.
Radio interference with other devices.
Change in wireless environment.
Move away from microwave ovens,
devices using a wireless LAN, or other
wireless devices.
Use the procedure below to set the
network again.
q Press the RESET/CONFIG button for
about 10 seconds so the indicator lights
red.
w Press the RESET/CONFIG button again
for about 3 seconds so the indicator
lights green.
e Next register the RC-7000CI again.
22
23
Specifications
Batteries: LR03/AAA Type (four batteries)
Battery service life:
Approx. 3 months
(depending on usage frequency)
Frequency: 2,405 MHz 2,475 MHz (15 ch)
Bandwidth 2 MHz
Radio frequencies:
2.4 GHz
Modulation method: O-QPSK
Spectrum spread system:
DSSS
Communication distance:
30 m (varies with the environment)
Maximum external dimensions:
63 (W) x 233 (H) x 28 (D) mm
(
2-31/64” x 9-11/64” x 1-7/64”)
Weight: 170 g (Approx 6.0 oz)
Troubleshooting Specifications

Denon Brand Company, D&M Holdings Inc.
TOKYO, JAPAN
www.denon.com
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon rc 7000 ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon rc 7000 ci in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon rc 7000 ci

Denon rc 7000 ci User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info