584585
58
Zoom out
Zoom in
Previous page
1/71
Next page
InformationHDMI Control FunctionPlaybackSetupConnectionsGetting Started Specications
ENGLISH

If a problem should arise, rst check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem
persist, there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
Troubleshooting
Symptom Cause / Countermeasure Page
Power does not turn
on.
Check if the power cord is properly connected.
Plug the power supply cord into the power outlet.
The safety protection device may be activated. Unplug the power
cord once, and wait for 5-10 seconds and then plug it in again.
DVD-A1UDCI enters the standby status by safety function when
the fan stops. Check the back of the set if something is disturbing
the fan rotation.
22
3, 9
Unable to play back
bonus view.
Does the SD Memory Card has more than 1GB of available space?
Has the SD Memory Card been initialized by the DVD-A1UDCI?
Was the SD Memory Card inserted while the power of the unit is
on. (Insert the SD Memory Card while the DVD-A1UDCI is in the
standby status.)
4, 38
32
4, 38
Picture does not
appear.
Switch the TV's input setting to the external input connected to
the player.
Is the Pure Direct function set to “On”? Set to “Off”.
Also, is “Pure Direct SetupVideo Outon the GUI menu set
to Offat the “User Preset 1” or “User Preset 2” setting? Set it
to “On”.
Check the connection of the video/S-Video/component video cable.
Does the “Video Setup” – “Component Resolution” setting on the
GUI menu match the connected device's resolution? Set it so that
it matches.
30, 40
19
26
Video and audio are
not output with HDMI
connection.
Check the connection of the HDMI cable.
Is the “HDMI” indicator of the display of the DVD-A1UDCI
lighting?
Is the Pure Direct function set to “On”? Set to “Off”.
Also, is “Pure Direct SetupVideo Outon the GUI menu set
to Offat the “User Preset 1” or “User Preset 2” setting? Set it
to “On”.
Check whether the connected display device or other device
supports HDCP. This unit will not output a video signal unless the
other device supports HDCP. See the owner’s manual of your TV,
AV Amp, etc.
Check that the setting of the HDMI video resolution supports the
resolution of the connected device. When set to Auto”, DVD-
A1UDCI makes the setting automatically.
Check that the HDMI mode setting matches the connected
content. The connection method of each HDMI mode is different.
13, 14
8
30, 40
16
15
13, 14
Symptom Cause / Countermeasure Page
HD audio is not
output.
Set “BD Audio Mode” to “HD Audio Output”. 33
Picture is not
displayed or is
disturbed.
Picture of a BD-Video
or DVD-Video disc is
in black and white.
The picture may be slightly disturbed directly after fast-forwarding
or reversing. This is not a malfunction.
Connect the DVD-A1UDCI’s video/S-Video/component video
output either directly to the TV or to the TV via the AV Amp. Do
not connect via a VCR (video cassette recorder). Some discs
include copy prohibit signals, and when such discs are played
via a VCR, the copy guard system may cause the picture to be
disturbed.
Is a disc that is not compatible with the player or a disc with
a different region number loaded? (This player supports region
code “A” for BD-Video discs, “1” or “ALL” for DVD-Video discs.)
19
3
No sound is heard or
the sound is hard to
hear.
Check the devices whose audio is connected and the speaker
connections.
Is the power of devices whose audio is connected turned on?
Is the input selection set to the input to which the DVD-A1UDCI
is connected?
Is the audio output properly selected?
11 ~ 22
13 ~ 21
Picture freezes
momentarily during
playback.
When the disc is scratched or contaminated with ngerprints, the
disc may not be played back correctly. Clean the disc or replace
with a non-scratched disc.
There may be a problem with the data recorded on the disc.
6
Playback does not
start even when 1 is
pressed, or starts but
stops immediately.
Is there condensation inside the player or on the disc? (Let set for
1 to 2 hours with the power off.)
When the disc is scratched or contaminated with ngerprints, the
disc may not be played back correctly. Clean the disc or replace
with a non-scratched disc.
Is the disc loaded upside-down? Load the disc properly, with the
side containing the signals to be played facing down.
Is an unplayable disc loaded?
3
6
6
3, 4
Subtitles are not
displayed.
Subtitles cannot be displayed for BD-Video, DVD-Video or DivX®
les that do not contain subtitles.
Is the subtitle setting “Off”? Use a disc menu or to set the
displayed subtitle.
48
25
SD Memory Card
cannot be read.
The format of the card does not match to this unit or the card is
not compatible.
Is the playback media mode set to “SD CARD MODE”?
Select “SD CARD MODE” at .
32
36
Troubleshooting
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DVD-A1UDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DVD-A1UDCI in the language / languages: English as an attachment in your email.

The manual is 12,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info