522888
33
Zoom out
Zoom in
Previous page
1/72
Next page
TroubleshootingInformationHDMI Control FunctionPlaybackConnectionsGetting Started Specications
ENGLISH
2
Setting items
Setting contents
Source Direct
Disable the speaker and
subwoofer settings and
output the disc audio as is.
NOTE
Set to within the playback
frequency band of the
amplier you are to use:
On at “50 kHz” or “100
kHz”. Setting outside the
frequency band can result
in damage to your amplier
and even re.
Off : Enable the speaker and subwoofer settings.
On : 50kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 50 kHz audio signals.
On : 100kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 100 kHz audio signals.
Setting On: 50 kHz” or On: 100 kHz” enables full-range playback on
all channels recommended for DTS. (Note that this results in a 5 dB
increase in subwoofer volume, and a 15 dB increase with Super Audio
CD). This also allows you to play back the 6-channel source of DVD-
Audio recorded on all channels with the full frequency range. In this
case, make an analog connection according to disc operating manual.
When set to “On: 50 kHz” or “On: 100 kHz”, all speaker sizes are set to
“Large” and “Yes” is set for the subwoofer.
Even when set to “On: 50 kHz” or On: 100 kHz”, “Channel Level” and
“Distance” settings are available.
Compression
Compresses the dynamic
range of Dolby TrueHD/
Dolby Digital/Dolby Digital
Plus audio. At night or other
times when you cannot play
back at high volume, this
compensates by reducing
high level sounds and
increasing low level sounds.
Auto : Automatically compress Dolby TrueHD audio dynamic range. The
sound is not compressed when playing signals other than Dolby TrueHD
signals.
Off : Dynamic Range compression is not applied.
Low : Set minimum dynamic range compression.
Middle : Set middle dynamic range compression.
High : Set maximum dynamic range compression.
AFDM
Automatically set the
surround mode by detecting
the surround mode
identication signal recorded
in the disc.
On : Automatically set surround mode when the ID signal is included.
Off : Do not set surround mode even when the ID signal is included.
MTRX : Create a surround audio signal by matrix processing, regardless
of the presence of an ID signal.
An EX ag may not be included for Dolby Digital EX sources. Even with
AFDM” set to “On”, set to “MTRX” in case the playback mode does not
automatically switch.
NOTE
This setting is valid when “Audio Setup– “7.1ch Audio Out” on the GUI
menu is set to (vpage 32) and when “HDMI SetupAudio Setupon
the GUI menu is set to “Multi LPCM BM On” (vpage 25).
This setting is invalid when “Audio Setup” – “Source Direct” on the GUI
menu is set to On(vpage 29), and when “DENON LINK Setup
“DENON LINK Mode” is set to anything other than “Off” (vpage 30).
This function is invalid for the DTS-CD source.
Audio Setup
Setting items
Setting contents
BD Effect Sound
Sets for a click sound and
other outputs during BD
popup menu operations.
On : Outputs BD effect sound.
Off : Does not output BD effect sound.
BD Re-Encoder
Sets the format during
output of the BD’s Mix Audio
signal from the digital output
terminal.
Auto : Outputs primary audio (main audio) in the same type of audio
format. Dolby Digital/Dolby Digital Plus/Dolby TrueHD are output as
Dolby Digital, DTS/DTS-HD are output as DTS and Linear PCM is output
as Linear PCM.
Dolby DigitalOutputs to the digital audio output terminal (optical/
coaxial) with Dolby Digital.
DTS : Outputs to the digital audio output terminal (optical/coaxial) with
DTS.
Valid when “BD Audio Mode” is set to “Mix Audio Output (vpage
33).
Digital Out
Set the audio signal of digital
audio output.
For more information on each
audio signal, refer to Audio
Signal from the Digital Audio
Output (Optical/Coaxial)
Terminal” (vpage 17).
Bitstream : Outputs a bitstream signal. Converts Dolby TrueHD, Dolby
Digital Plus to Dolby Digital, and DTS-HD to DTS for output.
PCM : Output the downmixed audio signal to 2ch LPCM.
PCM Down Sampling : Convert sampling frequency audio greater than
48 kHz to a 48 kHz 2ch LPCM audio output signal.
When outputting CD, etc. to a digital recording device such as the CD
recorder, convert to PCM or PCM down sampling.
When a disc with recorded Linear PCM or PPCM (Packed PCM) is played
back, this outputs Linear PCM irrespective of the setting.
Downmix
Set the method used to
convert a multi-channel
audio signal to a 2-channel
signal.
Lt/Rt : Signals are converted to Dolby Surround compatible 2-channel
audio signals for output. This setting is valid for DTS-HD, DTS Digital
Surround, Dolby Digital Plus and Dolby Digital audio signals. (If the
connected AV Amp is Dolby Pro Logic compatible, AV Amp plays back
using surround audio.)
Stereo : Outputs by converting to the 2ch (stereo) audio.
NOTE
In order to enable the “Lt/Rt setting when playing back BD, set “BD
Audio Mode” to “HD Audio Output” (vpage 33).
Remote control operation
buttons
:
Displaying the menu
Cancel the menu
:
Moves the cursor
(Up/Down/Left/Right)
:Decision the setting :Return to previous menu
Setup
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DVD-A1UD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DVD-A1UD in the language / languages: English as an attachment in your email.

The manual is 12,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info