2
Use the • and ª cursor buttons to select the desired setting,
then press the ENTER button.
AUDIO CHANNEL
Use this to adjust for the connected speaker systems.
DIGITAL OUT
Use this to select the digital output’s signal format.
LPCM (44.1 kHz/48 kHz)
Use this to set the digital audio output when playing DVDs
recorded in linear PCM audio.
DENON LINK
Use this to output digital signals from the DENON LINK
terminal.
IEEE1394
Use this to output digital signals from the IEEE1394 terminal.
SOURCE DIRECT
This permits a setting to output the audio without adding
speaker settings or channel level processing to the audio
signals of DVD audio or Super Audio CD.
BASS ENHANCER
Set whether or not to output audio signals from the
subwoofer when playing two-channel audio signals.
✽ The BASS ENHANCER settings do not apply to digital
outputs.
3
Use the • and ª cursor buttons to select the desired setting,
then press the ENTER button.
q When “AUDIO CHANNEL” is selected:
B
Use the
•
and
ª
cursor buttons to select the item to be
set, then press the ENTER button.
MULTI CHANNEL (Factory default)
Select this for systems in which three or more speakers
are connected.
When MULTI CHANNEL is set, the speaker settings
(SPEAKER CONFIGURATION), speaker output level
adjustment (CHANNEL LEVEL) and speaker distances
(DELAY TIME) can be set.
2 CHANNEL
Select this for systems in which only two speakers are
connected.
1
See page 14.
Remote control unit
3
B
When “MULTI CHANNEL” is selected, use the
•
and
ª
cursor buttons to select the item to be set, then press the
ENTER button.
SPEAKER CONFIGURATION
Use this to select the types of the different speakers.
CHANNEL LEVEL
Use this to adjust the output level of the different
speakers.
DELAY TIME
Use this to set the distance from the different speakers to
the listening position.
✽
To exit the SPEAKER SETUP mode
Use the
ª
cursor button to select “AUDIO SETUP” then
press ENTER button.
✽
The SPEAKER CONFIGURATION settings only apply to
analog outputs.
B
When “SPEAKER CONFIGURATION” is selected, use the
•
and
ª
cursor buttons to select the speaker to be set
then press the ENTER button.
• The type of speaker used for the front speakers, center
speaker, subwoofer and surround speakers can be set.
Use the
•
and
ª
cursor buttons to select the speaker
type, then press the ENTER button.
LARGE
Select this when a large speaker is connected.
SMALL
Select this when a small speaker is connected.
NONE
Select this when no speaker is connected.
YES
Select this when a subwoofer is connected.
NO
Select this when no subwoofer is connected.
• When “CROSSOVER” is selected:
40 Hz, 60 Hz, 80 Hz (Factory default), 100 Hz, 120 Hz,
set the frequency of cross over.
✽
Press the RETURN button to return to the “SPEAKER
SETUP” menu.
B
When “CHANNEL LEVEL” is selected, use the
•
and
ª
cursor buttons to select the speaker to be adjusted, then
use the
0
and
1
cursor buttons to set the level.
TEST TONE
• Use the
0
and
1
cursor buttons to select auto or
manual.
Adjust so that the volume of the test tones output from
the different speakers sounds the same.
• The volume level output from the front speakers (left
and right channels), center speaker, surround speakers
(left and right channels) and subwoofer can be adjusted.
• The volume level can be adjusted between 0 and -10 dB
in steps of 1 dB.
• Settings SW + 10 dB to “ON” increases by 10 dB the
volume level that is output from the sub woofer.
✽
Press the RETURN button to return to the “SPEAKER
SETUP” menu.
Remote control unit
Remote control unit
