584583
9
Zoom out
Zoom in
Previous page
1/40
Next page
6
Introduction Introduction
ENGLISH
ENGLISH
Keep in mind the following when using the remote control:
Make sure that there are no obstacles between the remote
control and infrared sensor window on the unit.
Remote operation may become unreliable if strong sunlight or
fluorescent light is shining on infrared sensor window of the
unit.
Remote control for different devices can interfere with each
other. Avoid using remote control for other equipment located
close to the unit.
Replace the batteries when you notice a fall off in the operating
range of the remote control.
The maximum operable ranges from the unit are as follows.
If you have other DENON's DVD players around this unit, this unit
reacts to the commands you made for DVD players through its
remote control. To avoid this situation, you can set this unit not
react to other DENON's DVD player's remote control.
1) In stop mode, press [SETUP].
2) Press [7],[8],[9],[2].
3) Press [SETUP].
“Only Attached Remocon” will be displayed on the upper
right corner of the screen and this unit only react to the
commands from this unit's remote control.
To set back to default, press [7],[8],[9],[1] at step 2. “Normal
Remocon” will be displayed on the upper right corner of the
screen and this unit react to both the commands from this unit's
remote control and the other DENON's DVD players' remote
control.
To avoid the other DENON’s BD players responding the remote
signal of this unit, you can change the signal code of the remote
control. If the signal code of the remote control does not match to
the signal code of the unit, you cannot control the unit with the
remote control.
Change the signal code of the unit
1) In stop mode, press [SETUP].
2) Use [Y / Z] to select , then press [ENTER].
3) Use [Y / Z] to select , then press [ENTER].
4) Use [U / V] to select “Remote Control Setting”.
5) Press [ENTER] to select “DENON1” or “DENON2”.
6) Press [SETUP] to exit.
At this point the new signal code of the unit is effective. Please
change the signal code of the remote control to match to the
signal code of the unit with following procedure.
Change the signal code of the remote control
Set to “DENON1”:
Press and hold [RETURN], and press [3], [2], [1].
Set to “DENON2”:
Press and hold [RETURN], and press [1], [2], [3].
If the signal code does not match, the signal code of the remote
control will be displayed on the front panel display.
The default setting and the setting after you change the
batteries is “DENON1”.
About the Remote Control
Loading the Batteries
A Open the battery
compartment cover.
B Insert two “AA” (R6P)
batteries, with each one
oriented correctly.
C Close the cover.
Cautions on Batteries
Use “AA” (R6P) batteries in this remote control.
Replace the batteries with new ones approximately once a
year, though this depends on the frequency with which the
remote control is used.
If the remote control does not operate within a close
proximity of the main unit, replace the batteries with new
ones, even if less than a year has passed.
The included batteries serve only for verifying operation.
Replace them with new batteries as soon as possible.
When inserting the batteries, be careful to do so in the
proper direction, following the and marks in the remote
control’s battery compartment.
To prevent damage or battery fluid leakage:
- Do not mix a new battery with an old one.
- Do not mix two different types of batteries such as alkaline
and manganese.
- Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
Remove the batteries when not planning to use the remote
control for a long period of time.
If the batteries should leak, carefully wipe off the fluid from
the inside of the battery compartment, then insert new
batteries.
Using a Remote Control
- Line of sight: approx. 23 feet (7m)
- Either side of the center: approx. 23 feet (7m) within 30°
Setting this Unit not React to Other DENON's DVD Player's Remote Control
Note
The setting remains after you turn off this unit or unplug the
AC cord.
If you try to operate this unit with the other DENON's DVD
players' remote control, some of the operation may not be
available depending on the manufactured year or type of the
remote control.
30°30°
23 feet (7m) 30° 23 feet (7m) 23 feet (7m) 30°
Changing the Signal Code of a Remote Control
Remote Control Setting
DENON1
Media Select Disc
Others
E5H01UD_V4_EN.book Page 6 Wednesday, October 15, 2008 10:37 AM
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DVD-2500BTCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DVD-2500BTCI in the language / languages: English as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon DVD-2500BTCI

Denon DVD-2500BTCI User Manual - Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info