614629
8
Zoom out
Zoom in
Previous page
1/14
Next page
Connections Fader Start
ENGLISH
Specifications
Rear Panel
q MAIN OUT (BALANCED) connectors
These XLR type connectors provide a balanced
line level output.
Connect these connectors to the balanced
analog input connectors on an amplifier or
console.
Pin layout: 1. GND, 2. Hot, 3. Cold
Applicable connector: Cannon XLR-3-31 or
equivalent.
w LEVEL ATT (Master out level attenuator)
Use this to attenuate the MASTER output level
(–10 dB).
Reference is 0 dB.
e MASTER MONO OUT ON/OFF switch
When this switch is on, mixed L and R signal is
outputted from the MASTER OUT.
r MAIN OUT (UNBALANCED) terminals
This stereo pair of RCA terminals provides a
unbalanced line level output.
Connect these terminals to the unbalanced
analog input terminals on an amplifier or
console.
t REC OUT terminals
This stereo pair of RCA terminals provides a
line level output. The signal is unaffected by the
Master Level control.
It is intended for use with a tape recorder, but is
not restricted to that purpose.
y BOOTH OUT (BALANCED) connectors
These 1/4” TRS type connectors provide a
balanced line level output with independent front
panel Zone Level controls and are not affected
by the Master Level control.
Connect these connectors to the balanced
analog input connectors on an amplifier or
console.
Pin layout: Tip: Hot, Ring: Cold, Sleeve: GND
Applicable connector: Cannon XLR-3-31 or
equivalent.
u SEND/RETURN terminals
These 1/4” TS mono terminals allow external
processing of the program signal.
When connect monaural type effect processor,
use Lch input and output.
i LINE 2, 4, 6, 8 FADER output terminals
Connect these terminals to the Fader input
terminals of the DN-S1200, DN-S3500, DN-
HS5500 and etc using the 3.5 mm stereo mini
cord.
o DUCKING ATTENUATION LEVEL control
DUCKING attenuation level can be adjusted.
(– ∞ ~ –20 dB)
Q0 AUX MIC input terminal
Accepts a balanced microphone with 1/4”
terminals.
Q1 MAIN MIC input terminal
Neutric combo terminal.
Accepts either a balanced microphone with an
XLR connector or a balanced microphone with
1/4” TRS balanced terminals.
Q2 PHONO 1, 2, 3 /LINE 1, 3, 5 switches
These switches change the Input from Phono to
Line level inputs.
These switches set Line level inputs when
Turntable is not connected.
Q3 PHONO 1, 2, 3 /LINE 1, 2, 3, 4, 5, 6, 7, 8 input
terminals
These stereo pairs of unbalanced RCA terminals
are Inputs for any line level device.
Q4 Phono Ground screws
This screws provide a place to connect the
ground wire from a turntable.
This terminal is exclusively for a turntable
grounding and not a safety earth ground.
Getting Started
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DN-X1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DN-X1100 in the language / languages: English as an attachment in your email.

The manual is 9,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info