614642
11
Zoom out
Zoom in
Previous page
1/36
Next page
11
ENGLISH
Each push of the i PLAY/PAUSE (13) button
switches between playback and pause.
PLAY/PAUSE (
13) button illuminates solid green
during playback and flashed in pause.
When the i PLAY/PAUSE (
13) button is pushed
during play, the DN-S3000 pauses playback at that
point. Push i PLAY/PAUSE (
13) button once
again and playback resumes.
When the Scratch mode is set to MAIN, the Platter
turns when the Main Track is played. When the
rotation of Scratch Disc is stopped by pressing with
the finger, the pause mode is set, and when the
finger is released playback resumes.
NOTE:
Standing up of playback
slows unusually after trans
porting the product.At the
time, push center of the !1
Scratch Disc lightly.
5
BASIC OPERATION
Play and pause
1
2
Push the #6 PITCH/KEY
button to PITCH LED lights up.
PITCH KEY (key adjust) OFF
Move the #5 Pitch slider to adjust
the pitch. The current pitch setting
is displayed on the display.
Pitch decreases
Pitch increases
When the !0 CUE button is pushed during playback,
the track stops and returns to the position that
current playback started (Cue point) and prepares
for next playback. This function is called Back-Cue.
With Back-Cue function, you can start from exactly
same position. The !0 CUE button illuminates solid
red when DN-S3000 is ready to start playback.
You can set and change Cue point as follows.
When you started playback.
Track select finished.
manual search.
Play and Cue
If you would not like to start playback from
beginning of the track, you need to move Cue Point
using fast Search and manual search function.
With Pitch slider you can adjust the playback speed
(Pitch).
If you would not prefer to change key of sound, use
the Key Adjust function.
Adjusting the pitch
3
DN-S3000 has five pitch ranges,
4%, 10%, 16%, 24% 50% and
100%.
When the #6 RANGE
button is pushed for more than 1
sec, the pitch range can be
selected with the #0
PARAMETERS knob.
4
After you found your
preferred Cue point, push
the !0 CUE button then new
Cue point is set.
2
Push the @9 SCRATCH
MODE button for more than
1 sec to set @9 Scratch Disc
to search mode. The
SCRATCH MODE button
LEDs will turn off.
3
Turn the !1 Scratch Disc to
change Cue point. You can hear
the short sound of the current
Cue point.
When !1 Scratch Disc is turned in the pause,
standby or frame repeat mode, works as the
manual search function.
With PITCH BEND function you can change pitch
temporary. DN-S3000 has three ways for this
function PITCH BEND buttons and Scratch Disc.
Pitch Bend
1
3
[PITCH BEND +/ buttons]
Push the #3 PITCH BEND
or #4 + button for
momentary change of
pitch.
While holding these buttons down, the pitch
continues to change up to the limitation.
After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
[Scratch Disc]
When the Scratch mode is
set to SEARCH, the playback
speed can be changed by
turning !1 Scratch Disc
during playback.
The pitch increases gradually when the
Scratch Disc is turned clockwise and
decreases when turned counterclockwise.
When you stop turning the Scratch Disc, the
playing speed returns to the previous pitch.
PITCH BEND
2
When the Scratch source is
set to MAIN and the Platter is
turning, playback of the Main
source can be slowed
temporarily by lightly pressing
!1 Scratch Disc or PLATTER.
In addition, playback can be quickened
temporarily by pushing Scratch Disc or
PLATTER in the direction in which the Platter
is turning.
Turn the #0 TRACK knob.
By pushing #0 TRACK knob down while turning, the
tracks will change 10 at a time.
Select the track
!
Move the Cue point
1
You can move to the approximate playback
start position by #1 or #2 FAST SEARCH
buttons.
[1-MIN.SKIP]
If the FAST SEARCH button
is pushed short time, the
playback position skips for about 1 minute.
[FAST SEARCH]
When the FAST SEARCH button is pressed
and held in, the disc is fast-searched.
Relay playback
Relay Play function is a playback mode to continue
play tracks of CDs in two DN-S3000s.
Connect the X-EFFECT IN/OUT terminals between
two DN-S3000s.
1
Start Relay Play
q Push the RELAY button
for more than 1 sec to
enable Relay play mode.
You can set Relay mode
as below.
In the single play mode, when the one
players playback reaches end of track,
another DN-S3000 starts playing.
In the continuous play mode, when the
whole tracks on one side are finished,
another DN-S3000 starts.
The discs in two DN-S3000s can be
played alternately by setting both DN-
S3000 to the relay play mode.
Relay play can be set in the program and
random play modes.
Relay play is possible also for DN-S3000
or DN-S5000.
2
Stop Relay Play
w When the RELAY button
is pushed for more than 1
sec while in the relay play
mode, the relay play
mode is turned off.
Power on play
When POWER ON PLAY is set to ON at ⁄4
PRESET (8), playback starts from the first track on
the disc when the power is turned on.
q, w
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DN-S3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DN-S3000 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info