584582
50
Zoom out
Zoom in
Previous page
1/69
Next page
ENGLISH

TroubleshootingInformationSetupConnectionsGetting Started Specications
Operations Enabled During Playback
During playback of a BD or DVD-Video recorded with several
camera angles, you can change the angle.
Switching the Angle
BD
DVD-V
NOTE
Angle changing may be restricted, depending on the disc.
1
Press during playback.
The angle number currently being played is displayed.
Angle
1/3
2
Use to select angle.
Angle
2/3
3
Press .
The setup screen disappears.
Press .
The display brightness each time the button is
pressed.
Normal Dim Dark Off
Changing the Brightness of the
Display (Dimmer Control)
Even when Off is selected, the status of operations that are
performed appears momentarily on the display if “Display Setup”
– “Temporary Display” on the GUI menu is set to “On” (vpage 30).
When you make an HDMI connection with a TV or AV Amp compatible
with DBP-4010UDCI and HDMI control functions, you can perform
the following operations by setting the HDMI control function of each
device.
TV or AV Amp power is turned on by operating the
DBP-4010UDCI, and functions change with DBP-
4010UDCI input.
Turning off the TV’s power turns the DBP-
4010UDCI’s power to standby.
Operating the DBP-4010UDCI via the TV’s remote
control.
(When the TV’s remote control has player operation buttons)
n
n
n
If the HDMI control function does not operate properly, check the
following points.
Is the TV or AV Amp compatible with the HDMI control function?
Are the HDMI control function settings of all equipment correct?
(Step 3)
After setting, did you add another HDMI device connection or
make any changes in the connections? In this case, perform setting
again.
HDMI Control Function
NOTE
The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
Some functions may not operate depending on the connected TV
or AV Amp. Check the owner’s manual of each device for details
beforehand.
When “Other Setup “Power Saving” on the GUI menu is set
to “Power Saving Standby or “Normal Standby” (vpage 31),
the player’s power cannot be turned on using the HDMI control
function.
When “HDMI Setup– “HDMI Control” – “Power Off Control” on the
GUI menu is set to “Off(
vpage 24), the DBP-4010UDCI is not set
to standby even if the connected device is in the standby mode.
When “DENON LINK Setup “DENON LINK Mode” on the GUI
menu is set to “4th”, the HDMI control function is enabled for the
connected devices.
1
Set HDMI control function to “On”.
On the GUI menu, set “HDMI Setup” “HDMI Control” (vpage
24).
2
Turn the power on for all the equipment connected by
HDMI cable.
3
Set the HDMI control function for all equipment
connected by HDMI cable.
On the GUI menu, set the DBP-4010UDCI with “HDMI Setup
– “HDMI Control” (vpage 24).
Please refer to the owner’s manual as regards setting of connected
devices.
Carry out Steps 2 and 3 should any of the equipment be
unplugged.
b
b
4
To ensure that the DBP-4010UDCI’s HDMI video
output is projected on the TV screen, change the
input function of the TV and AV Amp.
5
When you turn the TV’s power to standby, check that
the power of the DBP-4010UDCI and AV Amp also
goes on standby.
Playback HDMI Control Function
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DBP-4010UDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DBP-4010UDCI in the language / languages: English as an attachment in your email.

The manual is 11,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info