584582
23
Zoom out
Zoom in
Previous page
1/69
Next page
TroubleshootingInformationHDMI Control FunctionPlaybackSetupGetting Started Specications
ENGLISH
20
System Requirement
Internet Connection by Broadband Circuit
Modem
Device that connects to the broadband circuit and conducts communications on the Internet.
A type that is integrated with a router is also available.
Router
When using the DBP-4010UDCI, we recommend a router with the following features.
Built-in DHCP (Dynamic Host Conguration Protocol) server.
Function that automatically assigns an IP address on the LAN.
Built-in 100BASE-TX switch (built-in switching hub compatible with speeds upwards of 100 Mbps)
Ethernet cable (CAT-5 or greater recommended)
An Ethernet cable is not included with the DBP-4010UDCI.
For Ethernet cable, we recommend you use shielded straight cable (normal type).
If you use the at type or a non-shielded cable, the noise may adversely affect other devices.
For Internet connection, use an ISP (Internet Service Provider). Ask your local dealer for details.
NOTE
It is necessary to subscribe to an ISP in order to connect to the Internet. If you already have a
broadband connection, there is no need to subscribe anew.
• The router you can use varies with the ISP. For more information, contact your ISP or PC dealer.
DENON assumes no responsibility whatsoever for any communication errors or troubles resulting
from customer's network environment or connected devices.
Others
The DBP-4010UDCI can use the DHCP function to automatically set the network.
With the type of circuit in which network setting is performed manually, when subscribed to a provider,
conduct the setting in accordance with “Network Setup” on the GUI menu (vpage 29).
If you connect the DBP-4010UDCI to a network without a DHCP function, conduct IP address and other
settings according to “Network Setup” on the GUI menu (vpage 29).
The DBP-4010UDCI does not support PPPoE. If you subscribe to a circuit that is set with PPPoE, a
PPPoE-compatible router is required.
When setting manually, check the setting contents with the network administrator.
n
n
n
n
n
Connecting the Power Cord
Connect the included power cord to the DBP-4010UDCI, and plug it into an AC outlet.
Power cord
(included)
To household power
outlet (AC 120 V, 60 Hz)
NOTE
Be sure to insert the power plug rmly. Incomplete connection results in noise generation.
Once Connections are Completed
On the GUI menu, when “Other SetupAuto Power Mode” – On(vpage 31), the following states are
maintained for about 30 minutes, and then the power is turned automatically to standby.
Turning the Power On
When power is switched to standby
Either press on the unit, or press on the remote control.
The power indicator lights red.
n
NOTE
During power standby, a slight amount of power is consumed. To totally cut off the power, remove the
power cord from the power outlet.
Press the unit’s or the remote control’s .
The power is turned on, and the power indicator lights green.
“LOADING” appears on the display, and disc information is read.
The “NO DISC” message is displayed when a disc is not loaded. b
(DBP-4010UDCI)
(Remote control
unit)
Disc not loaded
Playback has stopped
Stopped due to resume function
5. Using BD-LIVE function or updating the software version of DBP-4010UDCI
Connections
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DBP-4010UDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DBP-4010UDCI in the language / languages: English as an attachment in your email.

The manual is 11,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info