139732

Denon dbp 4010ud Manual

11
Zoom out
Zoom in
Previous page
1/70
Next page
ENGLISH
TroubleshootingInformationHDMI Control FunctionPlaybackSetupConnections Specications
Inserting the Batteries
About the Remote Control Unit
e Put the rear cover back on.
q Remove the remote control
unit’s rear cover.
w Set three R6/AA batteries in
the battery compartment in the
indicated direction.
NOTE
Use R6/AA batteries in this remote control.
Replace the batteries with new ones if the set does not operate
even when the remote control unit is operated close to the unit.
(The supplied batteries are only for verifying operation.)
When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
To prevent damage or leakage of battery uid:
Do not use a new battery together with an old one.
Do not use two different types of batteries.
Do not attempt to charge dry batteries.
Do not short-circuit, disassemble, heat or dispose of batteries in
ames.
If the battery uid should leak, carefully wipe the uid off the inside
of the battery compartment and insert new batteries.
Remove the batteries from the remote control unit if it will not be in
use for long periods.
Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
•
•
•
•
•
•
•
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating
it.
30°
30°
Approx. 7 m
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong articial light from an inverter type uorescent lamp or infrared
light.
Remote Control Settings (Remote
Control Side)
Switches when the DBP-4010UD’s remote control operates
another DENON BD players in the vicinity.
Set the remote control code simultaneously on the main unit, too.
For how to set codes, see GUI menu: “Other Setup” – “Remote
Control Setting” – “Remote ID” (vpage 31).
GRemote control code settingH
1
: Set the remote control code to “1”.
2
: Set the remote control code to “2”.
If the signal code of the remote control does not match the signal
code of the unit, the remote control code set on the unit is shown
on the display.
GExampleH
If the code setting on the unit is “DENON 1”, and the setting on the
remote control is “2”, “PLAYER 1” is shown on the display.
NOTE
Match the signal code of the remote control with the signal code of
the unit. If the remote control code is different, you cannot operate
the DBP-4010UD with the remote control.
Even if you change the remote control code, set GUI menu “Other
Setup” – “Remote Control setting” – “Receive Legacy Remocon”
(vpage 31) to “Off” when operating the DBP-4010UD with a
remote control other than DENON’s.
•
•
•
Getting Started
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon dbp 4010ud at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon dbp 4010ud in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 11,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info