451156
51
Zoom out
Zoom in
Previous page
1/74
Next page
47
ENGLISH
Basic version Advanced versionSimple version Information
Remote control
Operating range of the remote control
Point the remote control at the remote sensor when operating it.
30°
30°
Approx. 7 m
NOTE
The set may function improperly or the remote control may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Inserting the batteries
q Slide the rear lid in the
direction of the arrow and
remove it.
w Load the two batteries
properly as indicated by
the marks in the battery
compartment.
R6/AA
e Put the rear cover back on.
If the battery level is low, the remote control signal transmission/
status display flashes 5 times when a button is pressed.
In this case, replace the batteries soon.
If the batteries are completely exhausted, the remote control signal
transmission/status indicator goes dark.
NOTE
Insert the specified batteries in the remote control.
Replace the batteries with new ones if the set does not operate
even when the remote control is operated close to the unit.
(The supplied batteries are only for verifying operation.)
When inserting the batteries, be sure to do so in the proper direction,
following the q and w marks in the battery compartment.
To prevent damage or leakage of battery fluid:
Do not use a new battery together with an old one.
Do not use two different types of batteries.
Do not attempt to charge dry batteries.
Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
Do not keep the battery in a place exposed to direct sunlight or in
places with extremely high temperatures, such as near a heater.
If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
Remove the batteries from the remote control if it will not be in use
for long periods.
Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
Remote control settings (remote control side)
Switches when this unit remote control operates another
DENON BD players in the vicinity.
Set the remote control code simultaneously on the unit, too
(vpage39 “Remote ID”).
1
Hold POWER ON and OPEN/CLOSE pressed
simultaneously.
While these buttons are held pressed, the remote control signal
transmission/status display flashes twice, and the remote
control enters Setup mode.
2
When the number button “1” is
pressed, the remote control ID is
set to “DENON 1”.
When the number button “2” is
pressed, the remote control ID is
set to “DENON 2”.
When number key input is completed and the remote control
signal transmission/status display flashes twice, the settings for
the remote control are completed.
If the signal code of the remote control does not match the signal
code of the unit, the remote control code set on the unit is shown on
the display.
GExampleH
If the code setting on the unit is “DENON 1”, and the setting on the
remote control is “2”, “PLAYER 1” is shown on the display.
NOTE
If you made the remote control settings incorrectly, the remote
control signal transmission/status display flashes for 2 seconds, and
then goes off. If this happens, the settings are incorrect and retry
the settings.
Match the signal code of the remote control with the signal code of
the unit. If the remote control code is different, you cannot operate
the this unit with the remote control.
Even if you change the remote control code, set the GUI menu
“Other”-“Receive Legacy Remocon” (vpage39) to “Off” when
operating this unit with a remote control other than DENON’s.
1.DBP2012E2_ENG_10A.indd 47 2011/07/22 17:25:23
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DBP-2012UD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DBP-2012UD in the language / languages: Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 11,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon DBP-2012UD

Denon DBP-2012UD User Manual - English - 74 pages

Denon DBP-2012UD User Manual - German - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info