451156
29
Zoom out
Zoom in
Previous page
1/74
Next page
25
ENGLISH
Advanced versionSimple version InformationBasic version
Video resolution
This section is for making the settings for television resolution. Set them depending on the connected
television.
Press RESOLUTION.
The resolution is changed as shown below each time RESOLUTION is pressed.
The default settings is underlined.
Auto
480/576i
1080P24
1080P
1080i
480/576P
720P
Source Direct
(Auto)
(1080 progressive, 24-frame)
(Source direct)
(1080 progressive)
(480/576 interlaced)
(1080 interlaced)
(480/576 progressive)
(720 progressive)
This unit’s component video output supports 480i/576i/480p/576p/720p/1080i output.
If the Video resolution is not set to “Auto”, set it to correspond with the resolution of your television.
Images will not be projected normally if the television resolution and this unit’s output resolution do not
match.
Audio and video will be temporarily interrupted if the power of the connected device currently playing is
turned off, or the input is switched.
When you change the HDMI video resolution of the unit, it takes a few seconds up to about 10 seconds
for validation between the unit and the connected device. Audio/video is not output during this period.
NOTE
When the HDMI video resolution is set to “1080P24”, a HDMI video signal is output from the unit with a
resolution of 1080P and a frame rate of 24 frames per second, regardless of the video signal on the disc
being played. Because of this, when playing discs containing video signals recorded with a frame rate
of something other than 24 frames per second, the movement of the picture may be unnatural. If this
happens, set the HDMI video resolution to something other than “1080P24”.
When you make the following settings, this unit will output video signals from an HDMI OUT connector
with a resolution of 1080P24 (1080 progressive, 24-frame).
RESOLUTION setting: Set to “Auto”, “Source Direct”, or “1080P24”.
HDMI mode setting: Set to “24P ON”.
Television resolution supports 1080P24 (1080 progressive, 24-frame).
Under these setting conditions, no video signals are output from VIDEO OUT and COMPONENT VIDEO
OUT connectors. To output video signals, press HDMI MODE and set HDMI output to “24P OFF”.
HDMI output settings
Most movies on Blu-ray disc are recorded at 24 frames per second, the same as movie film.
If the unit is set like this, images with the same quality as movies can be enjoyed.
The setting for outputting signals with 24 video frames in HDMI mode is made here. Then images with
fluid motion can be enjoyed when video of 1080P24 (1080 progressive, 24-frame) is played.
NOTE
You can not use HDMI mode while the GUI menu is displayed.
Press HDMI MODE.
The current status of HDMI output is displayed on the television screen.
Each time HDMI MODE is pressed, “24P ON” and “24P OFF” are toggled.
The default setting is “24P OFF”.
24P ON
If the connected television supports “1080P24”, use this setting.
After making settings, set Video Resolution to “1080P24” or “SourceDirect”.
24P OFF
If the connected television does not support “1080P24”, use this position.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon DBP-2012UD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon DBP-2012UD in the language / languages: English as an attachment in your email.

The manual is 13,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon DBP-2012UD

Denon DBP-2012UD User Manual - German - 74 pages

Denon DBP-2012UD User Manual - Dutch, French, Italian, Swedish, Spanish - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info