Manual Denon dbp 1610 (page 11 of 58) (English, German, Dutch, French, Italian)

139629

Zoom out

Zoom in

1/58

Introduction Introduction

ENGLISH

Introduction Connections Playback Function Setup Others

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote

control and infrared sensor window on the unit.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on infrared sensor window of the

unit.

• Remote control for different devices can interfere with each

other. Avoid using remote control for other equipment located

close to the unit.

• Replace the batteries when you notice a fall off in the operating

range of the remote control.

• The maximum operable ranges from the unit are as follows.

If you have other DENON’s DVD players around this unit, this unit

reacts to the commands you made for DVD players through its

remote control. To avoid this situation, you can set this unit not

react to other DENON’s DVD player's remote control.

1) In stop mode, press [SETUP].

2) Press [7],[8],[9],[2].

3) Press [SETUP].

• “Only Attached Remocon” will be displayed on the upper

right corner of the screen and this unit only react to the

commands from this unit's remote control.

• To set back to default, press [7],[8],[9],[1] at step 2). “Normal

Remocon” will be displayed on the upper right corner of the

screen and this unit react to both the commands from this unit's

remote control and the other DENON’s DVD players' remote

control.

To avoid the other DENON’s BD players responding the remote

signal of this unit, you can change the signal code of the remote

control. If the signal code of the remote control does not match to

the signal code of the unit, you cannot control the unit with the

remote control.

Ⅵ Change the signal code of the unit

1) In stop mode, press [SETUP].

2) Use [Y / Z] to select , then press [ENTER].

3) Use [Y / Z] to select , then press [ENTER].

4) Use [U / V] to select “Remote Control Setting”.

5) Press [ENTER] to select “DENON1” or “DENON2”.

6) Press [SETUP] to exit.

• At this point the new signal code of the unit is effective. Please

change the signal code of the remote control to match to the

signal code of the unit with following procedure.

Ⅵ Change the signal code of the remote control

Set to “DENON1”:

Press and hold [RETURN], and press [3], [2], [1].

Set to “DENON2”:

Press and hold [RETURN], and press [1], [2], [3].

• If the signal code does not match, the signal code of the main

unit will be displayed on the front panel display.

• The default setting and the setting after you change the

batteries is “DENON1”.

• If the code setting on the unit is “DENON1”, and the setting on

the remote control is “DENON2”, “PLAYER 1” is shown on the

front panel display.

About the Remote Control

Loading the Batteries

A Open the battery

compartment cover.

B Insert two “R6” (AA)

batteries, with each one

oriented correctly.

C Close the cover.

Cautions on Batteries

• Use “R6” (AA) batteries in this remote control.

• Replace the batteries with new ones approximately once a

year, though this depends on the frequency with which the

remote control is used.

• If the remote control does not operate within a close

proximity of the main unit, replace the batteries with new

ones, even if less than a year has passed.

• The included batteries serve only for verifying operation.

Replace them with new batteries as soon as possible.

• When inserting the batteries, be careful to do so in the

proper direction, following the and marks in the remote

control’s battery compartment.

• To prevent damage or battery fluid leakage:

- Do not mix a new battery with an old one.

- Do not mix two different types of batteries such as alkaline

and manganese.

- Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

• Remove the batteries when not planning to use the remote

control for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from

the inside of the battery compartment, then insert new

batteries.

Using a Remote Control

- Line of sight: approx. 7m

- Either side of the centre: approx. 7m within 30°

Setting this Unit not React to Other DENON’s DVD

Player’s Remote Control

Note

• The setting remains after you turn the unit to the standby

mode or unplug the AC cord.

• If you try to operate this unit with the other DENON’s DVD

players' remote control, some of the operation may not be

available depending on the manufactured year or type of the

remote control.

30°30°

7m 30° 7m 7m 30°

Changing the Signal Code of a Remote Control

Angle Icon

Screen Saver

Auto Power Off

Panel Display

Slide Show

DivX(R) VOD

Remote Control Setting

Others

Off

Bright

5sec

DENON1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Denon dbp 1610 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 6,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Denon dbp 1610 Manual

Product: