584418
15
Zoom out
Zoom in
Previous page
1/108
Next page

Getting Started Settings Playback Remote ControlZONE2 Information Troubleshooting Specifications
ENGLISH
Connecting the Speaker
Cables
Protection Circuit
If the core wires touch the rear panel and the
screws etc., or the ± sides touch each other, the
protection circuit will be activated and the power
indicator will flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker
output is isolated, and the power supply goes to
the standby state. If the power supply is turned off,
after the power supply cord is withdrawn, please
confirm that speaker cable and input cable are
connected.
Also, if replaying large sound levels by using
a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will rise,
and the protection circuit might be activated. The
power supply will go into the standby state, and the
power indicator will flash red at 2 second intervals.
In this case, please switch off the power supply,
and wait until the AVR-990 has cooled down, and
the surrounding ventilation is good.
Even if there are no problems with the surrounding
ventilation and connections, in the event of the
protection circuit becoming activated, due to
thinking that the AVR-990 has failed, please contact
DENON Service center after switching off.
w q
w q
w qw q
*/
w q
(R)
(L) (R)
w q w q
(L) (R) (L)
Subwoofer
Center
speaker
Front
speakers B
Front
speakers A
Surround
speakers
Subwoofer
with built-in
amplifier
NOTE
Connect so that the speaker cable core wires
do not protrude from the speaker terminal. The
protection circuit may be activated if the core
wires touch the rear panel or if the + and sides
touch each other (v“Protection Circuit”).
Never touch the speaker terminals while the
power supply is connected. Doing so could result
in electric shock.
Use speakers with an impedance of 6 to 16 Ω/ohms.
When using front A and B speakers simultaneously,
use speakers with an impedance of 8 to 16 Ω/
ohms.
wq wq
(R) (L)
When in the “Front A Bi-Amp” and “Front B Bi-
Amp” modes, the same signals are output from
the front speaker terminals and the AMP ASSIGN
terminals.
These connections make for higher quality playback
sound with no interference between the signals of
the bass and treble units.
When the “Amp Assign” setting (vpage 33) is
“Front A Bi-Amp” or “Front B Bi-Amp”, connect
as follows. (The illustration shows a connection
example for the Front A Bi-Amp speakers.)
NOTE
Use speakers compatible with bi-amp
connections.
When making bi-amp connections, be sure to
remove the short-circuiting plate or wire between
the speaker’s woofer and tweeter terminals.
Carefully check the left (L) and right (R) channels
and + (red) and (black) polarities on the speakers
being connected to the AVR-990, and be sure to
interconnect the channels and polarities correctly.
When using a banana plug
Tighten the speaker
terminal firmly before
inserting the banana plug.
n
1
Peel off about 0.03 ft/10
mm of sheathing from
the tip of the speaker
cable, then either twist
the core wire tightly or
terminate it.
2
Turn the speaker terminal
counterclockwise to
loosen it.
3
Insert the speaker cable’s
core wire to the hilt into
the speaker terminal.
4
Turn the speaker terminal
clockwise to tighten it.
AVR-990
Front speakers A
Speaker Connections
About Bi-amp Connections
For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see “Set the “Amp Assign”
Mode According to the Speaker Layout” (vpage 11).
Connections
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-990 in the language / languages: English as an attachment in your email.

The manual is 17,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-990

Denon AVR-990 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info