584400
13
Zoom out
Zoom in
Previous page
1/88
Next page
0
Getting Started Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Specifications
w q
w q
(R)
(L)
w q
w q w q
(L) (R)
*/
w q w q
(L) (R)
Speaker Connections
Example: 5.1/7.1-channels
Front speakers
A
Center speakerSubwoofer
Subwoofer
with built-
in amplifier
Surround speakers
b L : Left
R : Right
NOTE
For surround back speakers :
Since “Amp Assign” of AVR-789 is set to “ZONE2” by default, audio is not output from the surround
back speakers. When using the surround back speakers with MAIN ZONE, change the “Amp Assign”
setting to “7.1ch” (vpage 31).
When using just one surround back speaker, connect it to the left channel (SBL).
For ZONE2 speakers :
For multi-zone connection and operation, see “Amp Assign / Multi-zone Connections and Operations”
(vpage 65 ~ 68).
Surround back
speakers
Connect when using
7.1-channel.
Connections
Connecting the Speaker Cables
Carefully check the left (L) and right (R) channels
and + (red) and (black) polarities on the speakers
being connected to the AVR-789, and be sure to
interconnect the channels and polarities correctly.
1
Peel off about 0.03 ft/10 mm
of sheathing from the tip of
the speaker cable, then either
twist the core wire tightly or
terminate it.
2
Turn the speaker terminal
counterclockwise to loosen
it.
3
Insert the speaker cable’s
core wire to the hilt into the
speaker terminal.
4
Turn the speaker terminal
clockwise to tighten it.
When using a banana plug
Tighten the speaker terminal firmly before
inserting the banana plug.
NOTE
Use speakers with an impedance of 6 to 16
Ω/ohms. When using front A and B speakers
simultaneously, use speakers with an impedance
of 12 to 16 Ω/ohms.
Connect the speaker cables in such a way that
they do not stick out of the speaker terminals.
The protection circuit may be activated if the core
wires touch the rear panel or if the + and sides
touch each other (v “Protection circuit”).
Never touch the speaker terminals while the
power supply is connected. Doing so could result
in electric shock.
Protection circuit
If the core wires touch the rear panel and the
screws etc., or the ± sides touch each other, the
protection circuit will be activated and the power
indicator will flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker
output is isolated, and the power supply goes to
the standby state. If the power supply is turned
off, after the power supply cord is withdrawn,
please confirm that speaker cable and input cable
are connected.
Also, if replaying large sound levels by using
a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will
rise, and the protection circuit might be activated.
The power supply will go into the standby state,
and the power indicator will flash red at 2 second
intervals.
In this case, please switch off the power supply,
and wait until the AVR-789 has cooled down, and
the surrounding ventilation is good.
Even if there are no problems with the surround-
ing ventilation and connections, in the event of
the protection circuit becoming activated, due to
thinking that the AVR-789 has failed, please con-
tact DENON Service center after switching off.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-789 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-789 in the language / languages: English as an attachment in your email.

The manual is 8,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-789

Denon AVR-789 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info