498716
124
Zoom out
Zoom in
Previous page
1/144
Next page
0
Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsTroubleshooting
ENGLISH
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
Troubleshooting
Symptom Cause / Countermeasure Page
Set does not operate
properly.
Reset the microprocessor. 123
Power does not
turn on, or turns off
directly after it was
turned on.
Check that the power plugs are securely inserted into the AVR-
4810’s AC inlet and the wall power outlet.
27
No sound is produced
from speakers.
Check the connections to the input devices and the speaker cable
connections.
Check the connections to the playback devices and select the
appropriate input source.
Adjust the master volume to an appropriate level.
Cancel the mute mode.
Disconnect the headphones. No sound is output from the speakers
or the PRE OUT terminals when headphones are connected.
Select an input source for which the digital input setting has been
made.
Match the terminal to which the digital input terminal is assigned
with the input mode.
14 ~ 26
17 ~ 26, 30
76
76
76
58
61
Display is off. Set “Dimmer“ to a setting other than “OFF”.
Cancel the PURE DIRECT mode. The display turns off when in
the Pure Direct mode.
55
80
“DOLBY DIGITAL
indicator does not
appear on display.
Check the Blu-ray Disc player / DVD player’s audio output setting.
For details, read the Blu-ray Disc player / DVD player’s operating
instructions.
GGeneralH
Symptom Cause / Countermeasure Page
Power switches off
suddenly while you
are using the AVR-
4810, the power
indicator will flash
in red at intervals
of approximately 2
seconds.
The protection circuit will be activated depending upon the
temperature rise in the internal parts of the unit. Please switch off
power at once, and re-apply the power after the body temperature
has fallen sufficiently.
Please re-install AVR-4810 in a place having good ventilation.
Power switches off
suddenly while you
are using the AVR-
4810, the power
indicator will flash
red at intervals of
approximately 0.5
seconds.
Please use speakers which have the specified impedance.
The protection circuit has been activated because the core wires
of different speaker cables have touched each other or a core
wire has slipped out of the terminal and is touching the AVR-
4810’s rear panel. Unplug the power cord, then after twisting
the core wires together tightly again, or effecting termination
treatments etc, please reconnect once again.
16
16
Even applying
power, the power
display flashes
red at intervals of
approximately 0.5
seconds.
The AVR-4810 amplifier circuit has failed. Switch off the power
and please contact the DENON service adviser.
GRemote Control UnitH
Symptom Cause / Countermeasure Page
Set does not work
properly when remote
control unit operated.
Batteries are worn. Replace with new batteries.
Operate the remote control unit within a distance of about 7 m
from the AVR-4810 and at an angle of within 30°.
Remove the obstacle between the AVR-4810 and the remote
control unit.
Insert the batteries in the proper direction, checking the q and
w marks.
The set’s remote control sensor is exposed to strong light (direct
sunlight, inverter type fluorescent bulb light, etc.). Move the set
to a place in which the remote control sensor will not be exposed
to strong light.
Make sure the remote control IDs of the main unit and remote
control unit match. If the IDs do not match, “AVAMP z (z
is the main unit’s remote control ID) appears on the AVR-4810
display when the remote control unit is operated.
Set the remote control unit’s function button properly.
3
3
3
3
55, 104, 109
7
124


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-4810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-4810 in the language / languages: English as an attachment in your email.

The manual is 25,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-4810

Denon AVR-4810 User Manual - German - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info