498663
14
Zoom out
Zoom in
Previous page
1/142
Next page
10
ENGLISH
11
On the
STEP3
screen, use ui
to select “Next Calculation”, and
then press ENTER.
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
STEP4 Calculation
Now calculating...Please wait.
27%
Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
Set up speakers (Audyssey
®
Auto Setup)
STEP 4
Calculation
STEP 5
Check
12
Use ui to select the item you want
to check, and then press ENTER.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Next Store
Select item to check
Enter Cancel
Crossover Check
Ch.Level Check
Distance Check
Spkr Config Check
STEP5 Check
Check processing results.
To proceed,pressNext.
Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
If you want to check another item, press
RETURN.
13
Use ui to select “Next Store”
and then press ENTER.
14
Select “Store” and then press ENTER.
Save the measurement results.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
STEP6 Store
Now storing... Please wait.
78%
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
RETURN
Apply and store measurement result
Enter Cancel
Store
STEP6 Store
Press “Store” to store calculation results.
Saving the results requires about 20 seconds.
If the measuring results are not to be saved,
press RETURN. A message “Cancel auto
setup?” will be displayed. Press o then select
“Yes”. All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
NOTE
If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (vpage11). Then carry out Audyssey
Auto Setup again.
If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
If you change speaker positions or orientation,
perform Audyssey Auto Setup again to nd the
optimal equalizer settings.
STEP 6
Store
Finish
15
Unplug the setup microphone from
the units SETUP MIC jack.
16
Set Dynamic Volume
®
.
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
No
Yes
Turn Dynamic Volume on and exit Auto Setup
Exit
Finish
Storing complete.
Auto Setup is now finished.
Please unplug microphone.
Turn on Dynamic Volume?
For details of Dynamic Volume settings, see
page 86.
n When turning Dynamic Volume on
Use u to select “Yes“, and then press ENTER.
The unit automatically enters “Evening” mode.
n When turning Dynamic Volume off
Use i to select “No“, and then press ENTER.
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
After performing Audyssey Auto Setup with two
subwoofers, do not change the channel distances
and levels of both subwoofers.
1.AVR4311E2_ENG_6th_0810.indd 10 2010/08/12 10:11:37
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-4311 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-4311 in the language / languages: English as an attachment in your email.

The manual is 23,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-4311

Denon AVR-4311 User Manual - German - 142 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info