498659
32
Zoom out
Zoom in
Previous page
1/125
Next page

Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey Auto Setup)
Do not remove the setup microphone until Audyssey Auto Setup is
completed.
When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
1
Check the speaker connections.
(vpage 13 “Speaker Connections”)
2
Turn on the TV and subwoofer power.
Change the TV input to AVR-4310 input.
3
Turn on the AVR-4310 power.
(vpage 23 “Turning the Power On”)
4
Connect the setup microphone to the SETUP MIC
jack of the AVR-4310.
The “Audyssey Auto
Setup” screen is displayed
when you connect the
setup microphone.
Sound
receptor
a Connect the Included Setup
Microphone
NOTE
Loud test sounds may be played during Audyssey MultEQ XT
automatic speaker setup. This is part of normal operation. If there
is background noise in room, these test signals will increase in
volume.
Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not
in use).
Operating MASTER VOLUME during the measurements will cancel
the measurements.
NOTE
Do not hold the microphone in your hand during measurements.
Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
If you subwoofer provides volume and crossover settings, set these
as shown below before starting the Audyssey Auto Setup.
Volume setting : “12 o’clock” position” or the middle of the gain
knob’s range.
Low Pass Filter setting : Low Pass Filter Setting to “Off”, or
“Maximum/Highest Frequency”.
Phase setting : 0°
Standby mode setting : “Off”
5
Mount the setup microphone on a tripod or stand
and place it in the main listening position.
When placing the setup microphone, adjust the height of the
sound receiver part to the level of the listener’s ear.
Setup
microphone
Settings
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-4310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-4310 in the language / languages: English as an attachment in your email.

The manual is 22,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-4310

Denon AVR-4310 User Manual - German - 125 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info