522887
26
Zoom out
Zoom in
Previous page
1/119
Next page

Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH
Specifications
Multi Zone
ZONE2 or ZONE3 Pre-out Connections
If another power amplifier or pre-main (integrated) amplifier is connected, the ZONE2 or ZONE3 pre-out
(variable or fixed level) connectors can be used to play a different program source in ZONE2 or ZONE3
the same time (vpage 77 ~ 81).
When using a component video cable to connect the AVR-4308 and input device, connect the ZONE2
monitor output to the component video connectors. When using an S-Video cable or a video cable, please
connect the cable to the video connectors.
The ZONE2 video out is only for ZONE2.
R
L
R
L
"69
065
"6%*0
3-
*/*/
7*%&0
"6%*07*%&0
$0.10/&/57*%&0
: 1# 13
*/
Monitor (ZONE2)
Power amplier
(ZONE2 or ZONE3)
Input
Output
Infrared
retransmitter
Infrared
sensor
Extension jack for future use.
NOTE
For the audio output, use high quality pin-plug cords so that no induction humming or noise is produced.
For instructions on installing and operating separately sold devices, refer to the respective devices
operating instructions.
To conduct multi-zone playback, see “Amp Assign / Multi-Zone Connections and Operations” (vpage
77 ~ 81).
External Controller
When using in combination with an RF Remote Controller (RC-7000CI, sold separately) or RF Remote
Receiver (RC-7001RCI, sold separately) two-way communication with an RF Remote Controller is
possible.
The AVR-4308’s status information as well as iPod and Internet audio music files can be browsed watching
the RF Remote Controller’s display. For details, refer to the operating instructions of the respective
devices.
When used in combination with an RF Remote Controller or RF Remote Receiver, make the settings at
GUI menu “Manual Setup” – Option Setup” – “2Way Remote” – “Used” (vpage 39).
RS-232C connector
This connector is used for an external controller.
b If you wish to control the AVR-4308 from
an external controller using the RS-232C
connector, perform the operation below
beforehand.
q Turn the AVR-4308’s power.
w Turn off the AVR-4308’s power from the
external controller.
e Check that the AVR-4308 is in the standby
mode.
Trigger output jacks
The power of an external device equipped with
a trigger input jack can be turned on and off in
association with operations on the AVR-4308. For
details, see GUI menu “Manual Setup” – Option
Setup” – “Trigger Out 1” or “Trigger Out 2”
(vpage 38).
Output level: 150 mA/12 V
Check the trigger input conditions of the
connected device.
If the trigger input level of the connected device
is higher than 150 mA/12 V and depending on
the short-circuiting conditions, the AVR-4308’s
protection circuit may be activated, in which case
“TRIGGER PROTECT” appears on the display. If
this happens, turn off the AVR-4308’s power and
disconnect the connected device.
Connections
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-4308A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-4308A in the language / languages: English as an attachment in your email.

The manual is 14,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info