498655
33
Zoom out
Zoom in
Previous page
1/112
Next page

Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey Auto Setup)
s Audyssey Auto Setup Preparations
around items indicate the default setting.
Perform the following settings if adjustments, etc., are required for
the speaker environment you’re using.
If you do not need to perform the following settings, or have already
completed them, select “Auto Setup Start” and then press ENTER.
Proceed to “
STEP2
”.
When you are using surround back speakers with ZONE2/ZONE3,
set to “ZONE2” or “ZONE3”.
You can set in the same way as described in “Amp Assign” on page
33.
Change the Amplifier Assignment (Amp Assign)
The signal output from the SURR.BACK/AMP ASSIGN speaker terminal
of the AVR-3310 can be switched to match your speaker environment
(vpage 33 “Amp Assign”).
1
Press ui to select
“Amp Assign”, then
press ENTER.
2
Press o p to select Amp Assign Mode, then press
RETURN.
Normal
ZONE2
ZONE3
ZONE2/3-MONO
Front A Bi-Amp
Front B Bi-Amp
Front Height
: The surround back channel audio signals are
output.
: The ZONE2 audio signals are output.
: The ZONE3 audio signals are output.
: The ZONE2 / ZONE3 monaural audio signals are
output.
: The bi-amp audio signals are output. Set this for
bi-amp playback of the front A speakers.
: The bi-amp audio signals are output. Set this for
bi-amp playback of the front A speakers.
: The front height channel audio signals are output.
Audyssey Auto Setup detects the presence of each speaker and
automatically calculates the speaker size, channel level, distance and
crossover frequency settings. In addition, acoustical distortions are
corrected within the listening area.
When measuring begins, a test tone is output from each speaker.
Position and connect all speakers before commencing Audyssey
Auto Setup.
STEP2 Speaker Detection
1
Press ui to select “Auto Setup Start”, then press
ENTER.
2
Select “Measure”
and then press
ENTER.
3
Once all the speakers have been detected, check the
results of detection of the connected speakers.
4
Press ui to
select “Next 1
Measurement”, then
press ENTER.
Press u to select “Retry”, and when you press ENTER, measuring
at the main listening position starts again.
b
d Perform Audyssey Auto Setup
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
STEP1 Preparation
When “Amp Assign” is set to “Normal”, only then is “Surround Back”
displayed.
1
Press ui to select
“Channel Select”,
then press ENTER.
2
Press ui to select a channel, press o p to select
the item, and then press RETURN.
Frontn
A
B
A +B
: The sound is output from front speakers A when
measuring the front speakers.
: The sound is output from front speakers B when
measuring the front speakers.
:
The sound is output simultaneously from front speakers
A and B when measuring the front speakers.
Subwoofer, Surround Backn
Measure
Skip
: Measure the selected channel.
: Skip the selected channel and do not measure.
Set the channel to be measured (Channel Select)
Front
The front speaker to be measured can be selected ahead of time here.
Subwoofer, Surround Back
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
See overleaf
Settings
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-3310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-3310 in the language / languages: English as an attachment in your email.

The manual is 17,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-3310

Denon AVR-3310 User Manual - German - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info