65891
58
Zoom out
Zoom in
Previous page
1/96
Next page

Getting Started Connections Setup Playback Multi-Zone Information Troubleshooting
ENGLISH
MODE SELECTOR
Remote ID
AMP (MAIN)
TUNER
iPod
(Analog TUNER)
1
(Default)
81001 52863 72815
2 82001 52795 72816
3 83001 52800 72817
4 84001 52805 72818
3
Refer to the table at the below, and use [NUMBER] to
input the 5-digit number corresponding to the remote
ID to be changed.
The signal transmission indicator flashes twice.
4
Press [TU] (
mode) or [iPod] to select the mode
to be set.
5
Repeat steps 2 to 4 to set the remote IDs for all
modes.
NOTE
When changing a setting, be sure to set the same remote ID as the
AVR-2808’s (vpage 32).
When changing the AMP mode’s remote ID, also change the
“TUNER” and “iPod” remote ID at the same time.
Set the remote ID of an analog tuner for TUNER ( ).
[ AMP]
[NUMBER]
[MODE SELECTOR]
[RC SETUP]
[ TU]
[ iPod]
[POWER ON]
[CHANNEL +/–]
[SYSTEM CALL]
4
Press the button to be set.
The main remote control unit’s display turns off.
b If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
b If you want to learn other buttons, repeat steps 4 and 5.
b The mode can be switched by pressing [MODE SELECTOR].
b The signal transmission indicator lights once for a long time if
learning was not possible
6
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
With some remote control units, the signals cannot be learned or the
device will not operate properly even when the signals have been
learned. In this case, use the devices own remote control unit.
Learned buttons have priority over the preset memory. If you no
longer need the learned setting, reset the learning function (vpage
56).
NOTE
[HOME] cannot be learned.
Do not learn any remote control signals at [RC SETUP].
The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot
be learned.
Signal transmission
indicator
Remote Control
[8], [9],
[6], [7],
[1], [3], [2]
[ TV]
Setting the Remote ID
When using multiple DENON AV receivers in the same room,
make this setting so that only the desired AV receiver operates.
1
Press [AMP] to set the main remote control unit to the
AMP mode.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
Learning Function
If your AV devices are of a brand other than DENON or if they
cannot be operated with the preset memory function, their
remote control signals can be transfered to stored in the AVR-
2808’s main remote control unit.
1
Press [MODE SELECTOR] for the device you want to
set.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Press [9], [7] and [5], in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
Other devices
remote control unit
AVR-2808’s main remote
control unit (RC-1068)
1.AVR2808E2_ENG.indd 58 2007/09/28 11:41:49
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2808 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2808 in the language / languages: English as an attachment in your email.

The manual is 11,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2808

Denon AVR-2808 User Manual - German - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info