584055
53
Zoom out
Zoom in
Previous page
1/78
Next page
0
Getting Started Connections Remote Control Information Troubleshooting Specifications
ENGLISH
Multi-ZoneSettings
Setting items Setting contents
Front Height
Set whether or not to use
the front height channel.
ON : Use the front height channel.
OFF : Do not use the front height channel.
This can also be set by pressing
.
Subwoofer ATT
Attenuate subwoofer level
when using EXT. IN mode.
ON : The input from the subwoofer channel is attenuated.
OFF : The input from the subwoofer channel is not attenuated. Usually use
in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
Subwoofer
Turn subwoofer output on
and off.
ON : The subwoofer is used.
OFF : The subwoofer is not used.
Default
Restores all the surround
parameter settings to their
defaults.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Setting items Setting contents
Tone Control
Sets the tone control function
ON and OFF.
This can be set when
“Dynamic EQ” (vpage
51) is set to OFF”.
ON : Allow tone adjustment (treble, bass).
OFF : Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
Bass
Adjusts the low frequencies.
This can be set when
“Tone Control” is set to
ON”.
–6dB ~ +6dB (0dB)
Treble
Adjusts the high
frequencies.
This can be set when
“Tone Control” is set to
ON”.
–6dB ~ +6dB (0dB)
Setting items Setting contents
MultEQ
Corrects the frequency
response of the different
speakers.
NOTE
“MultEQ” and “Manual
EQ” settings for which
“Not Used” has been set at
“EQ Customize(vpage
32) cannot be selected.
When using headphones,
“MultEQ” is set to OFF”.
Audyssey : Optimize frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to at
response.
Manual : Apply frequency response set with “Manual EQ” (vpage 51).
OFF : The “MultEQ” equalizer cannot be used.
When Audyssey”, Audyssey Byp. L/R” or Audyssey Flat” is
selected, ” lights.
After running Audyssey Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed
without increasing the number of speakers measured, only
lights.
This can also be set by pressing .
When the “Audyssey Auto Setup” (vpage 23) procedure is performed, the “MultEQ”, “Dynamic
EQ” and “Dynamic Volume” functions are enabled.
Operating conditions for each function
Dynamic EQ :
When “MultEQ” is set to ON”
Dynamic Volume :
When “Dynamic EQ” is set to ON”
Setting :
When “Dynamic Volume” is set to ON”
NOTE
If the speaker settings are changed after the Audyssey Auto Setup” procedure is performed,
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”
is displayed.
If this happens, either perform the Audyssey Auto Setup” procedure again, or perform the “Restore
operation (vpage 27) to restore the settings to as they were after the Audyssey Auto Setup”
procedure was performed.
MultEQ
Dynamic EQ
Dynamic Volume
Setting
: Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu
Remote control
operation buttons : Displaying the menu
Cancel the menu
Playback
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Making the MultEQ, Dynamic EQ and Dynamic Volume
Settings (Audyssey Settings)
Default settings are underlined.
Adjusting the Tone (Tone Control)
Default settings are underlined.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2310CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2310CI in the language / languages: English as an attachment in your email.

The manual is 15,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2310CI

Denon AVR-2310CI Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info