498633
27
Zoom out
Zoom in
Previous page
1/77
Next page

Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH
Setup
Auto Setup
Optimize settings for speakers in use.
F Menu screen F
1-1.Start Menu
Step1:Speaker Detection
Audyssey
MultEQ
at ear height at
Front Sp. A
Amp Assign
Start
Cancel
Please place microphone
main listening position.
The speaker connection and polarity are detected at the rst
measurement position. The following attributes are also determined
at this time: “Speaker Size, “Speaker Distance, “Channel Level”,
“Crossover Frequency”.
Once the measurements are completed, the results are displayed.
Step 1 : Speaker Detection
Start
Start Auto Setup.
The Audyssey MultEQ Auto Setup process automatically calculates
the size, level, distance, bass management crossover frequency, and
optimal settings for each speaker and subwoofer. Audyssey MultEQ
corrects acoustical distortions within the listening area.
Before starting, connect and position all your speakers.
Once started, MultEQ will play a series of test tones through each
speaker.
NOTE
Loud test sounds may be played during Audyssey MultEQ Automatic
Speaker Setup. This is part of normal operation. If there is background
noise in room, these test signals will increase in volume.
Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
Quiet the listening environment before beginning measurements and
refrain from talking. Turn off air conditioning units or other devices
that emit noise if at all possible as measurements may be affected
by these sounds.
Operating the MASTER VOLUME knob on the main unit or the MASTER
VOLUME buttons on the remote control unit during measurements
will cancel the measurements.
Do not change the speaker connections or subwoofer volume after
“Step 1”.
a Start Menu
The settings are performed automatically.
NOTE
Do not turn the power off while the settings are being stored.
Step 2 : Measurement
After completing a measurement position, move the microphone to
the next position.
Measure 6 positions (the main listening position and 5 other
surrounding positions). Although it is allowable to measure less than 6
positions, it is recommended to measure 6 for best results.
Step 3 : Calculation
When “Calculateis selected at “Step 2”, the measurements taken
are analyzed automatically to determine how the speaker system
interacts with the room.
The time required for this analysis depends on the number of speakers
connected. The higher the number of speakers, the longer the time
required for analysis.
Step 4 : Check
Once the auto setup procedure is complete, a measuring result
checking screen appears.
Select any item whose results you want to check to review the
results.
Values that are different from the actual distance may be set for
speakers with built-in lters (subwoofers, etc.). This is because fi lters
add electrical delay to the signal that should be compensated.
Step 5 : Store
The auto setup measurement results are stored in the AVR-2308.
Front Speaker
The front speaker to be measured can be selected ahead of time
here.
[Selectable items]
A
: Output test tone from front speakers A.
B
: Output test tone from front speakers B.
A + B
: Output test tone from front speakers A and B.
Amp Assign
Advanced setting : changes power amplifi er assignment.
For details, refer to Amp Assign” (vpage 30).
If an error message appears during the measurements, check “Error
Messages”, take the advised action, then start the measurements
again (vpage 24).
1.AVR2308E2_ENG_102.indd 27 2007/10/30 15:51:03
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2308 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2308 in the language / languages: English as an attachment in your email.

The manual is 9,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2308

Denon AVR-2308 User Manual - German - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info