Manual Denon AVR-1912 (page 127 of 134) (English)

498661

127

Zoom out

Zoom in

1/134

124

GAudioH

Symptom Cause/Solution Page

Audio is not output. •Check the connections for all devices.

•Check the speaker connections and conﬁgurations.

•Check whether the audio device power is turned on.

•Adjust the master volume.

•Cancel the mute mode.

•Select a suitable input source.

•Select a suitable input mode.

•Disconnect the headphones. No sound is output from the

speakers when headphones are connected.

C 3,

7,8,9,

10,11,12

C 6,

51,52,53,

54,55,56

–

21, 68

20, 68

100

109

No sound is

produced from

surround speaker.

•Check if the surround speakers are connected to the SURROUND

terminals.

–

No sound is

produced from

surround back

speaker.

•Check if “Amp Assign” is set appropriately in order to output

audio from the surround back speakers.

•Set “Speaker Conﬁg.” – “S.Back” on the menu to something

other than “None”.

•Set “Surr.Parameter” – “S.Back” on the menu to something

other than “OFF”.

•Set the surround mode to something other than “STEREO” and

“VIRTUAL”.

No sound is

produced from front

height speaker.

•Set “Surr.Parameter” – “PLgz Height” on the menu to “ON”.

•Check if “Amp Assign” is set appropriately in order to output

audio from the front height speakers.

•Set “Speaker Conﬁg.” – “F.Height” on the menu to something

other than “None”.

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “Subwoofer Mode” is set to “LFE”, no sound may be output

from the subwoofers, depending on the input signal or selected

surround mode.

C 6,

51,52,53,

54,55

–

83, 84

Symptom Cause/Solution Page

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”.

100

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections.

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set

to other than “None”. If the speaker system is 2.0/2.1ch, this

surround mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

–

Audyssey MultEQ

XT, Audyssey

Dynamic EQ

and

Audyssey Dynamic

Volume

cannot be

selected.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

•When headphones are used, MultEQ

XT, Dynamic EQ

and

Dynamic Volume

cannot be selected.

–

Dynamic EQ

and

Dynamic Volume

cannot be selected.

•Run Audyssey

Auto Setup.

13, 56

RESTORER cannot

be selected.

•Check that an analog signal or PCM signal (fs=44.1/48 kHz) is

input. For playback of multichannel signals such as Dolby Digital

or DTS surround, RESTORER cannot be used.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

GRadioH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

•Change the antenna orientation or position.

•Separate the AM loop antenna from the unit.

•Use an FM outdoor antenna.

•Separate the antenna from other connection cables.

GControl dock for iPodH

Symptom Cause/Solution Page

iPod cannot be

played.

•Check the iPod connections.

•Insert the AC adaptor of the iPod control dock into the power

outlet.

•Switch the input source to “DOCK”.

–

Basic version

Advanced version

InformationInformation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-1912 in the language / languages: English as an attachment in your email.

The manual is 31,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-1912

Denon AVR-1912 Quick start guide - English - 16 pages

Denon AVR-1912 User Manual - German - 134 pages

Denon AVR-1912 Quick start guide - Spanish - 16 pages

Denon AVR-1912 User Manual - Spanish - 133 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Denon AVR-1912 Manual

Product: