60741
14
Zoom out
Zoom in
Previous page
1/81
Next page
w qw q
(R) (L)
w q
w q w q
(L) (R)
*/
w q w q
(L) (R)
Speaker Connections
Example: 5.1 / 7.1-channels
Front speakers A Center speakerSubwoofer
Subwoofer
with built-in
amplifier
Surround speakers
b L : Left
R : Right
NOTE
For surround back speakers :
When using just one surround back speaker, connect it to the left channel (SBL).
For ZONE2 speakers :
When outputting audio from the surround back speakers with ZONE2, set to “ZONE2” with “Manual
Setup” – “Option Setup” – “Amp Assign” from the menu. For multi-zone connection and operation, see
“Amp Assign / Multi-zone Connections and Operations” (vpage 60 ~ 62).
Connections
Connecting the Speaker Cables
Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being
connected to the AVR-1909, and be sure to interconnect the channels and polarities correctly.
1
Peel off about 10 mm of sheathing from the tip of the speaker cable,
then either twist the core wire tightly or terminate it.
2
Turn the speaker terminal counterclockwise to loosen it.
3
Insert the speaker cable’s core wire to the hilt into the speaker
terminal.
4
Turn the speaker terminal clockwise to tighten it.
NOTE
Use speakers with an impedance of 6 to 16 Ω/ohms. When using front A and B speakers simultaneously,
use speakers with an impedance of 12 to 16 Ω/ohms.
Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The
protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each
other (v “Protection circuit”).
Never touch the speaker terminals while the power supply is connected. Doing so could result in electric
shock.
Protection circuit
If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protec-
tion circuit will be activated and the power indicator will flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the
standby state. If the power supply is turned off, after the power supply cord is withdrawn, please con-
firm that speaker cable and input cable are connected.
Also, if replaying large sound levels by using a speaker having an impedance less than that specified (eg,
4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply
will go into the standby state, and the power indicator will flash red at 2 second intervals.
In this case, please switch off the power supply, and wait until the AVR-1909 has cooled down, and the
surrounding ventilation is good.
Even if there are no problems with the surrounding ventilation and connections, in the event of the pro-
tection circuit becoming activated, due to thinking that the AVR-1909 has failed, please contact DENON
Service center after switching off.
Surround back
speakers
0
Getting Started Setup Playback Remote Control Multi-zone Information Troubleshooting
ENGLISH
Specifications
Connect when using 7.1-
channel.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-1909 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-1909 in the language / languages: English as an attachment in your email.

The manual is 7,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-1909

Denon AVR-1909 User Manual - English - 103 pages

Denon AVR-1909 Quick start guide - English - 2 pages

Denon AVR-1909 User Manual - German - 81 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info