583938
23
Zoom out
Zoom in
Previous page
1/67
Next page
0
Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting
ENGLISH
Specifi cations
Step 4 : Check
To proceed to “Step 5” without checking the analysis result, use u i to select “Store<”
while “Parameter Check<” is displayed.
Values that are different from the actual distance may be set for speakers with built-in lters
(subwoofers, etc). This is because lters add electrical delay to the signal that should be
compensated.
NOTE
Do not turn the power off while the settings are being stored.
Step 5 : Store
The auto setup measurement results are stored in the AVR-1609.
q Press o while “Store<” is displayed.
“Storing” blinks on the display panel while the results are being stored.
When storing is complete, “Completed” is displayed followed by “Disconnect Mic”.
w Disconnect the setup microphone from the AVR-1609.
s Error Messages
If the auto setup procedure could not be completed due to speaker installation, the measuring environment,
etc. an error message is displayed. Check the relevant items and be sure to take the necessary measures. After
addressing any issues, perform the auto setup procedure over again.
NOTE
Be sure to turn the power off before checking speaker connections.
Select “Retry” to make the measurements again.
Error messages (examples) Cause Measures
M i c o r S p : N o n e
The included setup microphone is not
connected.
Not all speakers could be detected.
Connect the included setup
microphone to SETUP MIC jack.
Check the speaker connections.
A m b i e n t N o i s e
Too much noise in the room for
accurate measurements to be made.
Speaker or subwoofer sound is too
low for accurate measurements to be
made.
Either turn off any device generating
noise or move it away.
Try again when the surroundings are
quieter.
Check the speaker installation and the
direction in which the speakers are
facing.
Adjust the subwoofer’s volume.
C a u t i o n : S p N o n e
The messages alternate
F R
Displayed speaker could not be
detected.
· The front L and front R speakers
were not properly detected.
· Only one channel of the surround
speakers was detected.
· Sound was output from the R
channel when only one surround
back speaker was connected.
· The surround back speaker was
detected, but the surrounds were
not detected.
Check the connections of the
displayed speaker.
C a u t i o n : P h a s e
The messages alternate
S B L
Displayed speaker connected with
the polarities reversed.
Check the polarities of the displayed
speaker.
For some speakers, this error
message may be displayed even if the
speaker is properly connected. If the
connection is correct, use the u or i
buttons to display “Skip<” and then
press o.
n To switch to another analysis result item
Press ENTER.
This returns you to analysis results items, so repeat operation q.
n To proceed to “Step 5 : Store”
During display of crossover frequency result or analysis results item, press ENTER.
“Store<” is displayed.
n To cancel storing
Use u or i to display “Cancel<” while “Store<” is displayed and press o.
All the measured auto setup data will be erased.
When analysis is complete, “Parameter Check<” is displayed.
Press o and check the analysis results for the following four items.
q Make your selection using ui and press o.
Presence and size of speaker
“SpConfi g. Check<”
Distance of speaker from listening position
“Distance Check<”
Speaker channel level
“Ch Level Check<”
Crossover Frequency
“Crossover Check<”
w Use u or i to change which speaker is displayed.
Setup
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-1609 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-1609 in the language / languages: English as an attachment in your email.

The manual is 6,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-1609

Denon AVR-1609 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info