571793
83
Zoom out
Zoom in
Previous page
1/128
Next page
0
Getting Started Connections Setup Playback Multi-Zone Information Troubleshooting Specifications
Setting the Remote ID
When using multiple DENON AV receivers in the same room,
make this setting so that only the desired AV receiver operates.
1
Press [AMP] to set the main remote control unit to the
AMP mode.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Refer to the table at the right, and use [NUMBER] to
input the 5-digit number corresponding to the remote
ID to be changed.
The signal transmission indicator flashes twice.
4
Press [TU], [iPod] or [NET/DTU] to select the mode to
be set.
5
Repeat steps 2 to 4 to set the remote IDs for all modes.
NOTE
When changing a setting, be sure to set the same remote ID as the
AVP-A1HDCI’s (vpage 43).
When changing the AMP mode’s remote ID, also change the
“TUNER”, “iPod” and “NET/DTU” remote ID at the same time.
Set the remote ID of an analog tuner for “TUNER” ( ), the XM
remote ID for “ ”.
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
b If you want to learn other buttons, repeat steps 4 and 5.
b The mode can be switched by pressing [MODE SELECTOR].
b The signal transmission indicator lights once for a long time if
learning was not possible
6
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
[NUMBER]
[MODE SELECTOR]
[RC SETUP]
[ NET/DTU]
[ TU]
[ AMP]
[ iPod]
Other device’s
remote control unit
AVP-A1HDCI’s main remote
control unit (RC-1067)
Learning Function
If your AV devices are of a brand other than DENON or if they
cannot be operated with the preset memory function, their remote
control signals can be transfered to stored in the AVP-A1HDCI’s
main remote control unit.
1
Press [MODE SELECTOR] for the device you want to
set.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Press [9], [7] and [5], in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
4
Press the button to be set.
The main remote control unit’s display turns off.
b If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
With some remote control units, the signals cannot be learned or the
device will not operate properly even when the signals have been
learned. In this case, use the device’s own remote control unit.
Learned buttons have priority over the preset memory. If you no
longer need the learned setting, reset the learning function (vpage
82).
NOTE
[HOME] cannot be learned.
Do not learn any remote control signals at [RC SETUP].
The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes
cannot be learned.
Signal transmission
indicator
MODE
SELECTOR
Remote ID
AMP
(MAIN)
TUNER
iPod
NET/DTU
(Analog
TUNER)
(XM)
(Net
Audio)
(HD
Radio)
1
(Default)
81001 52863 52864 72815 62865 62840
2 82001 52795 52812 72816 62837 62841
3 83001 52800 52813 72817 62838 62842
4 84001 52805 52814 72818 62839 62843
Remote Control
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVP-A1HDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVP-A1HDCI in the language / languages: Spanish as an attachment in your email.

The manual is 17,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVP-A1HDCI

Denon AVP-A1HDCI Quick start guide - English - 2 pages

Denon AVP-A1HDCI User Manual - English - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info