571793
31
Zoom out
Zoom in
Previous page
1/128
Next page

Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting Specifications
Error Messages
If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over
again.
Error messages (examples) Cause Measures
No microphone or speaker Included setup microphone is not connected.
Not all speakers could be detected.
The front L speaker was not properly detected.
Connect the included setup microphone to the
SETUP
MIC jack on the main unit.
Check the speaker connections.
Ambient noise is too high
or Level is too low
Too much noise in the room for accurate
measurements to be made.
Speaker or subwoofer sound is too low for
accurate measurements to be made.
Either turn off any device generating noise or move it
away.
Try again when the surroundings are quieter.
Check the speaker installation and the direction in which
the speakers are facing.
Adjust the subwoofer’s volume.
None Displayed speaker could not be detected.
· The front R speaker was not properly detected.
· Only one channel of the surround (A) and
surround (B) speakers was detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
· The surround back or the surround (B) speaker
was detected, but the surround (A) speaker
was not detected.
· When the subwoofer configuration is set at
“2SP L/R”, “2SP MIX”, “3SP L/R/LFE” or “3SP
MIX”, the subwoofer could not be detected.
Check the connections of the displayed speaker.
Phase Displayed speaker connected with the polarities
reversed.
If the XLR pre-out terminal is used, the polarity is
reversed.
Check the polarities of the displayed speaker.
Check the polarity setting for the XLR output of the
displayed pre-set channel.
For some speakers, this error message may be displayed
even if the speaker is properly connected. If you are sure
that the wiring is correct, select “Skip”.
Room EQ
Select room EQ setting method.
[Selectable items]
All
Assign
s Option
Select settings for room EQ, mic, etc.
Direct Mode
Select room EQ use for DIRECT or PURE DIRECT mode.
[Selectable items]
ON
OFF
Mic Select
Select the microphone type if not using supplied mic.
The microphone connected to V.AUX Lch is used.
[Selectable items]
Mic
V.AUX L
NOTE
Be sure to turn the power off before checking the speaker connections.
Select “Retry” to make the measurements again.
Only a professionally certified installer should ever connect a
professionally-calibrated microphone to the V.AUX L input on the front
panel.
Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the
distance of the subwoofer manually.
Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If
this happens, THX recommends setting them manually.
Please note that any THX main speakers should be set to Small (80 Hz). If you set up your speakers using Auto Setup, please make sure
manually that any THX speakers are set to Small with 80 Hz crossover.
d Parameter Check
Check auto setup measurement results.
This is displayed after the auto setup procedure is
completed.
[Selectable items]
Spkr Config Check
Distance Check
Ch. Level Check
Crossover Check
EQ Check
Restore
The auto setup results can be reset to what was originally calculated
by MultEQ XT when “Restore” is selected.
Setup
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVP-A1HDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVP-A1HDCI in the language / languages: Spanish as an attachment in your email.

The manual is 17,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVP-A1HDCI

Denon AVP-A1HDCI Quick start guide - English - 2 pages

Denon AVP-A1HDCI User Manual - English - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info