616171

Denon AVC-A1HDA Manual

30
Zoom out
Zoom in
Previous page
1/117
Next page

Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting
Configuration
The speaker system to be measured can be selected ahead of time
here.
[Selectable items]
9.1
z1
7.1
z1
5.1
z1
9.2
z2
7.2
z2
5.2
z2
9.3
z3
7.3
z3
5.3
z3
z1: This can be set when “Subwoofer” is set to “1SP”.
z2: This can be set when “Subwoofer” is set to “2SP L/R” or “2SP
MIX”.
z3: This can be set when “Subwoofer” is set to “3SP L/R/LFE” or
“3SP MIX”.
Start
Start Auto Setup.
The Audyssey MultEQ XT Auto Setup process automatically calculates
the size, level, distance, bass management crossover frequency, and
optimal settings for each speaker and subwoofer. Audyssey MultEQ
XT corrects acoustical distortions within the listening area.
Before starting, connect and position all your speakers.
Once started, MultEQ XT will play a series of test tones through each
speaker.
If an error message appears during the measurements, check “Error
Messages” (vpage 27), take the advised action, then start the
measurements again.
Setting the correct speaker configuration can reduce the time required
to measure during the auto setup procedure as the system will not
have to look for speakers that are not connected.
STEP1 : Speaker Detection
The speaker connection and polarity are detected at the first
measurement position. The following attributes are also determined
at this time: “Speaker Size”, “Speaker Distance”, “Channel Level”,
“Crossover Frequency”.
Once the measurements are completed, the results are displayed.
NOTE
• Loud test tone may be played during Audyssey MultEQ XT Automatic
Speaker Setup. This is part of normal operation. If there is background
noise in room, these test tones will increase in volume.
• Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
• Quiet the listening environment before beginning measurements and
refrain from talking. Turn off air conditioning units or other devices
that emit noise if at all possible as measurements may be affected
by these sounds.
• Operating the
MASTER VOLUME knob on the main unit or the VOL
+/– buttons on the remote control unit during the measurements will
cancel the measurements.
• Do not change the speaker connections or subwoofer volume after
“STEP1”.
STEP2: Measurement
STEP3: Calculation
After completing a measurement position, move the microphone to
the next position.
Measure at least 6 positions (main listening position and at least 5 other
surrounding positions). For best results it is recommend measuring 6
or more positions (with a maximum of 8 positions).
NOTE
Do not turn the power off while the settings are being stored.
When “Calculate” is selected at “STEP2”, the measurements taken
are analyzed automatically to determine how the speaker system
interacts with the room.
The time required for this analysis depends on the number of speakers
connected. The higher the number of speakers, the longer the time
required for analysis.
STEP4: Check
Once the auto setup procedure is complete, a measuring result check
screen appears.
Select any item whose results you want to check to review the
results.
Values that are different from the actual distance may be set for
speakers with built-in filters (subwoofers, etc.). This is because filters
add electrical delay to the signal that should be compensated.
STEP5: Store
The auto setup measurement results are stored in the AVP-A1HD.
Subwoofer
The configuration of the measuring subwoofer can be selected
beforehand.
[Selectable items]
1SP
2SP L/R
2SP MIX
3SP L/R/LFE
3SP MIX
Setup
Pre-out Assign
Change the pre-out assignment.
[Selectable items]
Normal
Free Assign
XLR Out Polarity
Set to switch the XLR pre-out terminal polarity.
[Selectable items]
XLR
XLR (INV)
Set each channel.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVC-A1HDA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVC-A1HDA in the language / languages: English as an attachment in your email.

The manual is 14,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info