465793

DeLonghi PLS110AR Manual

31
Zoom out
Zoom in
Previous page
1/92
Next page
SINGLE SPLIT
11
ENGLISH
HANDLING
The outdoor unit must always be kept upright.
Handling must be done by suitably equipped qualified
technical personnel using equipment that is suitable for
the weight of the appliance.
Carefully remove the adhesive strips from the appliance.
After having removed the packaging, check that the con-
tents are intact and complete.
INSTALLING THE INDOOR UNIT
USER
USER
Before starting installation, decide on the position of the
indoor and outdoor units, taking into account the mini-
mum clearance required around the units (see technical
data table).
Install the indoor unit in the room to be air conditio-
ned, avoiding installations in corridors or communal
areas.
Ensure that there is a mains socket very close to the
indoor unit where it can be plugged in.
Install the indoor unit at a height of at least 2.5 m
from the ground.
LOCATING THE INDOOR UNIT
The indoor unit must be wall mounted.
It must be located so that the treated air can circula-
te throughout the room.
To install the indoor unit proceed as follows:
Installing the mounting plate
- Remove the screws from the plate, which is attached to
the rear of the unit.
- Remove the plate;
- Place it against the wall at the point where it is to be
installed, using a spirit level (provided in the kit) to
ensure that it is horizontal and complying with the mini-
mum clearance indicated in the figure.
- Using a pencil, mark the position of the holes for the
screw anchors on the wall.
- Drill 32 mm deep holes in the wall for fixing the plate.
- Insert the plastic anchors into the hole.
- Fix the mounting plate to the wall using the anchors
and the self-tapping screws provided in the kit.
- Check that the mounting plate is correctly fixed.
- Check again that the plate is level.
Drilling a hole in the wall for the piping
- Decide where to drill the hole in the wall for the piping
according to the position of the mounting plate (see
figure)
- Using compasses, mark the circumference (ø 90 mm) of
the hole for the connections to pass through.
The hole must be drilled in the left side of the unit in
line with the refrigerant outlet connections.
Note: when the product is delivered the mounting plate
is attached to the rear of the indoor unit. It may be a dif-
ferent shape to the one shown above, but the method of
installation is the same.
150 mm
150 mm150 mm
4,1 x 32
4,1x32
Mounting
plate
Plastic anchor
Outline of the unit
Recommended minimum clearance
(Ø 90 mm)
Plate (wall-
mounted)
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi PLS110AR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi PLS110AR in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info