800377
17
Zoom out
Zoom in
Previous page
1/124
Next page
16
Auto air ow: the appliance automatically chooses
the air ow based on the temperature selected and
the environmental conditions. This selection is only
available in conditioning mode.
SILENT FUCTION
(available in conditioning mode only
and on some models only)
By activating this function, the operating noise is further re-
duced. To activate it, press button (D6) on the remote
control. The display shows the relative symbol.
SELECT THE TEMPERATURE SCALE
The temperature can be displayed in °C or °F. To change the tem-
perature unit of measure select the air conditioning mode then
press both the decrease (D5) and increase (D4) keys for
about 3 sec.
SETTING THE TIMER
The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optimising
the operating periods.
How to program delayed shut down
While the appliance is on in any operating mode, delayed
shut down can be programmed.
Press the
C1C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D7), the timer symbol is dispaly-
ed and the hours light up.
Press the (D5) and (D4) buttons until the desired
numbers of hours to shut down appears on the display.
A few seconds after the timer is set, the setting is acquired, the
display shows the operating mode and the timer symbol stays lit.
Once the set time is elapsed, the air conditioner goes into standby.
To cancel the timer program, press the
C1C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D7)
twice. The timer symbol will go o.
How to program delayed start up
Plug in the appliance and set to standby.
Press the
C1C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D7), the timer symbol is dis-
palyed and the hours light up.
Press the (D5) and (D4) buttons until the desired
numbers of hours to start up appears. Start up can be pro-
grammed at any time within the 24 hours that follow.
When the set time is elapsed, the appliance will start to operate
in the same operating mode that was previously set.
To cancel the timer program, press the
C1C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D7)
twice. The timer symbol will go o.
SELFDIAGNOSIS
The appliance has a self diagnosis system to identify a number of warning/malfunctions.
Error messages are displayed on the appliance display.
IF ... IS DISPLAYED,
“Low Temperature
(Frost prevention)
..WHAT SHOULD I DO?
The appliance is tted with a frost protec-
tion device to avoid excessive formation of
ice. The appliance starts up again auto-
matically when the defrosting process is
completed.
IF ... IS DISPLAYED,
“Probe Failure”
(Probe damaged)
..WHAT SHOULD I DO?
If this is displayed, contact your local au-
thorized service center.
IF ... IS DISPLAYED,
“High Level”
(Internal tray full)
..WHAT SHOULD I DO?
Empty the internal safety tank following
the instructions in the section “End of
season operations”.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi PAC EM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi PAC EM in the language / languages: All languages as an attachment in your email.

The manual is 7.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info