ENVIRONMENTAL INFORMATION:
This unit contains fluorinated greenhouse gases covered
by the Kyoto Protocol.
Maintenance and disposal must be carried out by qua-
lified personnel only. (R134a - GWP=1300)
Transport, filling, cleaning, recovery and disposal
of refrigerant should be performed by the manu-
facturer's authorised Customer Services only.
The appliance should be disposed of by a specialist
centre authorised by the manufacturer only.
DESCRIPTION
A) Lid
B) Dasher
C) Removable cylinder
D) Function selector
E) Ventilation grille
F) Hollow to facilitate moving the appliance
G) Spatula
IMPORTANT:
1) Always close the lid "A" before operating the
dasher.
2) Do not leave the selector in the position
for more than 1 minute.
3) After turning the appliance off from " " to
" ", always wait at least 5 minutes befo-
re turning it on again.
4) The appliance must not be laid on its side or
turned upside down.
INSTRUCTIONS
ASSEMBLY AND DISSASSEMBLY
To take the appliance apart, remove the lid, then
remove the dasher from the pin in the centre of the
cylinder. Then remove the cylinder.
To reassemble the appliance, insert the cylinder and
press downwards on the edge with the hands (fig. 1).
Insert the dasher then fit the lid.
OPERATION
Assemble the appliance as described in the chapter
"ASSEMBLY AND DISSASSEMBLY".
You are recom-
mended (fig. 3) to moisten the aluminium bottom of
the appliance evenly with cotton wool dipped in
alcohol for food use taking care not to pour it onto
the central plastic area (fig. 3). Remember that
alcohol is inflammable. You should therefore per-
form this operation away from flames or hot stoves.
This prevents the formation of ice between the
cylinder and aluminium bottom of the appliance,
making it easier to extract the cylinder when pre-
paration is complete.
Place the ingredients required by the recipe in the
cylinder and fit the lid by turning anticlockwise.
Bear in mind that the cylinder holds a maximum of
600 g. Plug into a suitable mains socket. Make sure
there are no obstacles preventing air from circulating
freely through the grilles at the sides.
Once you have added all the ingredients to the cylin-
der, turn the appliance on by placing the selector in
the position.
Important: never use the appliance without the cylin-
der. Make sure the outside surface of the cylinder is
completely dry before inserting it in the appliance.
Process the ingredients by turning the selector to the
required position.
DESCRIPTION OF SELECTOR
The selector has 4 different positions:
Dasher rotation (compressor off)
Use this function to mix the ingredients during
the first phase of ice-cream preparation.
Important: you cannot add ingredients to the
cylinder while the dasher is in movement.
Appliance off.
Chilling (compressor operating)
Use this function to add or taste ingredients
during preparation or to stop the dasher to
check the texture of the ice-cream.
If the recipe requires ingredients to be added
(pieces of chocolate, raisins, meringues...),
turn the selector to the position for a maxi-
mum of 1 minute.
Important: you must never leave the appliance
in this position for more than 1 minute.
Leaving it in this position for longer could
seriously damage the dasher rotation mecha-
nism.
Combined dasher rotation and chilling (com-
pressor operating)
Use this function to make the ice-cream
through the combined action of the compressor
and the dasher.
When the ice-cream reaches the required tex-
ture, place the selector in the position to turn
the appliance off. Normally each ice-cream
making cycle lasts about 40 minutes.
Continuous functioning beyond this time will
result in excessively hard ice-cream and
serious damage to the dasher rotation mecha-
nism.
Important: if you need to work the ingredients with
a whisk (e.g., to froth the egg whites, beat the eggs
and sugar, etc.), you are recommended to prepare
the ingredients in a separate container and then
pour them into the cylinder.
8
