465726

DeLonghi HCS2030 Manual

6
Zoom out
Zoom in
Previous page
1/36
Next page
6
1. ELECTRICAL CONNECTIONS
- Before plugging into the mains, make sure the voltage of your mains supply corresponds to the
V value indicated on the appliance and that the socket and power line are appropriate for the
load required.
- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/EEC ON RADIO INTERFERENCE
SUPPRESSION.
2. Attaching the feet
To fit the feet, proceed as follows: Insert the foot into the guide on the side and push as far as it will
go until the two teeth hook in place (fig. 1).
3. Wall mounting
IMPORTANT: before drilling the wall, make sure the area is free of electrical wires or pipes. To fix
your convector heater to the wall, use the brackets “E” and “F” provided and appropriate screws and
anchors (provided).
Proceed as follows:
• Fix the brackets “E”, making sure the distances are as shown in fig. 3.
• Hang the heater on the two brackets fixed to the wall. Insert the two brackets “F” in the back of
the convector base as shown in fig. 4.
Mark the bracket fixing points on the wall. (When mounted, block the base of the heater in a fixed
position to prevent it being removed).
• Remove the heater, drill the wall and insert the anchors.
• Fix the heater again, inserting the brackets “F” into the base of the heater and fixing them to the
holes in the wall using the screws.
Now your heater is mounted on the wall.
The appliance must not be positioned directly underneath a fixed power point.
Position the appliance in such a way that the plug is easily accessible even after installation.
4. Operation and use
Turning on
Plug into the mains, turn the thermostat dial (B) to maximum and turn the appliance on by means of
the power selector (A) (fig.2) as described below:
• Turn the power selector knob (A) to the Min position to select minimum power (the Min power light comes
on).
• Turn the power selector knob (A) to the Med position to select medium power (the Med power light comes
on).
• Turn the power selector knob (A) to the Max position to select maximum power (the Max power
light comes on). In the fan version, both Min and Med lights come on.
5. Adjusting the thermostat
When the room has reached the required temperature, turn the thermostat dial (B) slowly anticlock-
wise until the lights go out and no further. The thermostat will automatically regulate the temperatu-
re set and keep it constant.
In spring or autumn or on mild days, you can save energy by using minimum power.
6. Frost prevention mode
With the thermostat dial in the position and one of the power levels selected, the appliance main-
tains room temperature at about 5°C, preventing freezing with minimal energy consumption.
7. Models with fan
A number of models have two fans for faster more even heating. To use this function, turn the power
selector (A) to the Max position (the corresponding light comes on).
8. Models with 24 hour timer (C)
To operate the appliance without the timer, place the timer pointer in the I position. To operate the
appliance at set times, position the pointer (D) in the position and proceed as follows:
• To operate the appliance without the timer, place the timer pointer in the I position. To operate the
GB
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi HCS2030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi HCS2030 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info