465835

DeLonghi HBP742T Manual

4
Zoom out
Zoom in
Previous page
1/28
Next page
4
ELECTRICAL CONNECTION
- Before plugging in the heater, check that the voltage of your domestic supply corresponds
to the voltage (V) indicated on the appliance.
- Check that the electrical socket has a rating of 10/16 Amps.
- THIS APPLIANCE CONFORMS TO DIRECTIVE EN 55014 GOVERNING RADIO INTERFE-
RENCE.
INSTALLATION
- Fix bracket to wall, complying with minimum measurement specified in fig. 1.
- Remove appliance from stand, by first turning black locking screw on top of stand 1/4
turn.
- Mount appliance on bracket and lock into place by turning black screw on top of bracket
(1/4 turn).
- Should appliance be installed in a bathroom, it must be mounted on the wall outside the
“safety area”, as shown in fig. 2.
- Only use appliance when fixed to a wall or mounted on its stand.
SWITCHING ON AND OFF PROCEDURE
To switch on appliance, whatever the function desired, put timer lever to position for conti-
nuous operation, or to position for “programmed” operation (see Timer section).
To switch off appliance, put timer lever to “0”.
SELECTOR KNOB
- Position A: Setting for hair dryer function
- Position B: Setting for hair dryer function + Heating at 1000 W without thermostat
- Position C: Heating at 1000 W without thermostat
- Position D: Heating at 2000 W with thermostat on maximum
- Position E: Anti-freeze function (appliance maintains room temperature at about 5°C, pre-
venting freezing with minimum energy consumption).
THERMOSTAT REGULATION
To regulate room temperature, proceed as follows:
- Put selector knob to position D;
- Wait for room temperature to reach comfort level desired, then slowly rotate selector knob
clockwise until warning light goes off.
The temperature thus set will be automatically maintained by the thermostat. Should further
temperature adjustment changes be required, turn knob clockwise to lower the temperature
and counter clockwise to raise it.
TIMER
For programmed function, appliance must be constantly connected to power supply.
For “programmed” heating, proceed as follows:
- For example, if time is 6 p.m., turn numbered dial of timer clockwise until number 18 is
aligned with pointer ▲ on timer.
- Set desired operating times by pushing inwards red teeth (fig. 4).
- Put timer lever to position . Appliance is now programmed to function automatically.
- To change programmed operating times, just push teeth back to original position and
reset timer for new functioning period.
- For use of appliance, outside preset timer programme, just put timer lever to position .
HAIR DRYER
Put timer lever to and selector knob to position A (also B = dual function).
Hair dryer works at 500 W with switch on handle set on position I; at 1000 W on position
II .
GB
HBP 20-06-2000 15:43 Pagina 4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi HBP742T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi HBP742T in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info