Manual DeLonghi ECAM350.50 - Dinamica (page 16 of 24) (English)

769999

Zoom out

Zoom in

1/24

10. When the water in the tank has run out, empty the con-

tainer used to collect the rinsing water;

11. Take out the water tank and ll with fresh water up to the

MAX level.

12. If the water softener lter was removed, replace it in its

housing in the water tank, and reposition the tank in the

appliance;

13. Empty

the container used to collect the descaler solution,

then position it under the hot water spout.

14. Press

OK (B15)

15. Hot water comes out of the hot water spout;

16. At the end of the second rinse, remove, empty and replace

the drip tray (A15) and grounds container (A11).

17. Empty the container used to collect the rinse water; re-

move the water tank from the machine, empty it and rinse

under running water, then ll with clean water up to the

MAX level and reposition it in the machine.

The descaling cycle is now complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. power

failure or disconnection from power supply), the machine

will prompt it to be completed when switched on again.

• WATER may nd its way into the grounds container (A11)

during the descaling cycle: this is quite normal;

• If the water tank has not been lled to the MAX level, at

the end of descaling, the appliance requests a third rinse to

guarantee that the descaler solution has been completely

eliminated from the machine's internal circuits.

• The appliance may request descaling cycles at very short

intervals. This is normal and due to the appliance’s ad-

vanced control system.

• THE descaling procedure can also be started by pressing

and holding the icon (B8).

18. SETTING WATER HARDNESS

The descaling alert is displayed after a period of time estab-

lished according to water hardness.

The machine is set by default for a hardness level of 4. The ma-

chine can also be programmed according to the actual hardness

of the local water supply, so that the descaling procedure will be

required less frequently.

18.1 Measuring water hardness

1. Remove the “TOTAL HARDNESS TEST” reagent strip (C1)

from its pack;

2. Immerse the strip completely in a glass of water for about

one second;

3. Remove the strip from the water and shake lightly. After

about a minute, 1, 2, 3, or 4 red squares will appear, de-

4. Place an empty container with a minimum capacity of 1.8

litres under the hot water spout (C6) and coee spouts (A9)

(g. 34); Press OK (B15);

1,8 l

Important! Danger of scalding

Hot water containing acid ows out of the coee spouts and

hot water spout. Take care to avoid contact with splashes of this

solution.

5. The descale programme starts and the descaler liquid

comes out of the hot water and coee spouts. A series of

rinses is performed automatically to remove all the scale

residues inside the coee machine. This is the longest

phase and may account for more than half the total des-

caling time.

After completing the descaling cycle, the appliance is ready to

be rinsed through with clean water.

6. Empty the container used to collect the descaler solution.

Remove the water tank from the machine, empty it and

rinse under running water, then ll with clean water up

to the MAX level (g 35) and reposition it in the machine.

MAX

7. Empty the container used to collect the descaler solution,

then position it under the coee spout and the hot water

spout (g. 34);

8. Press OK (B15);

9. Hot water is delivered rst from the coee spouts, then

from the hot water spout;

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi ECAM350.50 - Dinamica in the language / languages: English as an attachment in your email.

The manual is 9.35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi ECAM350.50 - Dinamica

DeLonghi ECAM350.50 - Dinamica User Manual - German - 28 pages

DeLonghi ECAM350.50 - Dinamica User Manual - Dutch, Danish - 168 pages

DeLonghi ECAM350.50 - Dinamica User Manual - French, Italian - 4 pages

DeLonghi ECAM350.50 - Dinamica User Manual - Portuguese, Swedish, Spanish, Norwegian, Finnish - 168 pages

DeLonghi ECAM350.50 - Dinamica Additional guide - All languages - 4 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeLonghi ECAM350.50 - Dinamica Manual

Product: