4. Select the required background by pressing the chosen
panel. The appliance goes back to the settings menu with
the new background;
5. Press “ ESC” to go back to the homepage.
8.16 Bluetooth
This function enables or disables the protection PIN to connect
to the appliance from a device.
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
BLUETOOTH” appears on the
display (B);
3. Enable or disable the PIN protection by pressing
or
;
4. Press “
ESC” to go back to the homepage.
The preset PIN is “0000”. You are recommended to customise the
PIN directly from the APP.
Please note!
The serial number of the appliance enables it to be identied
unambiguously when an association is created with the APP.
8.17 Demo mode
When this mode is enabled, the appliance’s main functions are
illustrated on the display:
1. Press “” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
DEMO MODE” appears
on the display (B);
3. Press “
“ to start the demo;
4. Press “ ESC” to go back to the homepage.
8.18 Default values
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
To reset the default values, proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
DEFAULT VALUES”
appears on the display (B);
3. Press ““ and then “ OK” to restore the original pa-
rameters (or “ ESC” to leave the parameters unaltered);
4. Press “ OK” to go back to the settings menu and “
ESC” to go back to the homepage.
8.19 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
STATISTICS” appears
on the display (B);
3. Press “
” to verify all the available statistics by pressing
< or >;
4. Press “ ESC” to go back to the homepage.
9. MAKING COFFEE
9.1 Selecting the coee aroma
Select the required aroma by pressing “ AROMA” (B6):
(see “9.6 Making coee
using pre-ground coee”)
EXTRA LIGHT AROMA
LIGHT AROMA
MEDIUM AROMA
STRONG AROMA
EXTRA STRONG AROMA
Custom (if programmed) /
Standard
9.2 Selecting the coee quantity
Select the required quantity of coee in the cup by pressing “
QUANTITY” (B7):
SMALL SIZE
MEDIUM SIZE
LARGE SIZE
EXTRA LARGE SIZE
Custom quantity (if pro-
grammed)/Standard quantity
14
9.3 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A5 - g. 10).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee is delivered too slowly or
not at all, turn one click clockwise to-
wards “7”.
For fuller bodied creamier coee, turn
one click anticlockwise towards “1” (do
not turn more than one click at a time
otherwise the coee could be delivered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.4 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle by selecting the “Rinse” function in
the settings menu (see section “8.1 Rinsing ”);
• warm the cups with hot water (using the hot water func-
tion, see section “12. Delivering hot water”);
• increase the coee temperature in the settings menu (see
section “8.10 Coee temperature ”).
9.5 Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
1. Fill the container (A3) (g. 11) with coee beans;
2. Place a cup under the coee spouts (A8);
3. Lower the spouts as near as possible to the cup (g. 12).
This makes a creamier coee;
4. Press <(B10) or > (B8) until the required coee is
displayed;
5. Then select your required coee:
• ESPRESSO
• DOPPIO+
• COFFEE
• LONG
• 2 ESPRESSO
6. Preparation begins. An image of the selected drink appears
on the display (B) together with a progress bar which grad-
ually lls as preparation progresses.
Please note:
• You can prepare 2 cups of ESPRESSO coee at the same
time by pressing “2X
“ during preparation of 1
ESPRESSO (the image is displayed for a few seconds at the
start of preparation).
• While the machine is making coee, delivery can be inter-
rupted at any moment by pressing “ STOP”.
• As soon as delivery has ended, to increase the quantity of
coee in the cup, just press “ EXTRA”. When the required
quantity is reached, press “ STOP”.
Once the coee has been made, the appliance is ready to make
the next drink.
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in section “23. Displayed
messages”.
• For hotter coee, see section “9.4 Tips for a hotter coee”.
• If the coee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section “9.3 Ad-
justing the coee mill” and section “24. Troubleshooting”.
• Preparation of each coee can be customised (see sections
“14. Customising the drinks” and “15. Memorising your
personal prole”).
9.6 Making coee using pre-ground coee
Important!
• Never add pre-ground coee when the machine is o or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty
the inside of the coee machine or block the funnel (A4).
Please note!
If you use pre-ground coee, you can only make one cup of cof-
fee at a time.
1. Press “
AROMA” (B6) repeatedly until “” (pre-
ground) appears on the display (B);
2. Open the pre-ground coee funnel lid (A2);
3. Make sure the funnel (A4) is not blocked, then add one
level measure of pre-ground coee (g. 13);
4. Place a cup under the coee spouts (A8) (g. 12);
5. Press the image corresponding to the required coee (ES-
PRESSO, COFFEE, LONG);
15
f
6. Preparation begins. An image of the selected drink appears
on the display, together with a progress bar which gradual-
ly lls as preparation progresses.
Important! Making LONG coee :
Halfway through preparation, the message “ADD PRE-GROUND
COFFEE, MAXIMUM ONE MEASURE” is displayed. Add one level
measure of pre-ground coee and press “ OK” .
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the rst coee is delivered.
10. MAKING CAPPUCCINOS AND MILKBASED
COFFEES
Please note!
• To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water con-
nection nozzle (A9) as described in sections “10.4 Cleaning
the milk container after every use”, “16.10 Cleaning the
milk container” and “16.11 Cleaning the hot water/steam
connection nozzle”.
10.1 Filling and attaching the milk container
1. Remove the lid (D2) (g. 14);
2. Fill the milk container (D3) with a sucient quantity of
milk, not exceeding the MAX level marked on the handle
(g. 15). Each mark on the side of the container corre-
sponds to about 100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If “Energy Saving” mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (g. 16);
4. Place the lid back on the milk container;
5. If present, extract the hot water/steam spout (C6) by press-
ing the release button (C7) (g. 17);
6. Attach the milk container (D) to the connection nozzle (A9)
(g. 18) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a suciently large cup under the coee spouts (A8)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(g. 19).
8. Follow the instructions below for each function.
10.2 Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coees.
Dial
position
Description Recommended for…
NO FROTHHOT MILK not frothed
CAFFELATTE
MIN. FROTHLATTE MACCHIATO / FLAT
WHITE
MAX. FROTH
CAPPUCCINO/ CAPPUCCI
NO+ / CAPPUCCINO MIX/
ESPRESSO MACCHIATO /HOT
MILK frothed
10.3 Making cappuccinos and milk-
based coees automatically
1. Fill the milk container (D) and attach it as described above.
2. Select the required drink:
• CAPPUCCINO
• LATTE MACCHIATO
• CAFFELATTE
• LATTE CALDO
• CAPPUCCINO+
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
3. A message on the display (B) instructs you to turn the froth
adjustment dial (D1) according to the froth required by the
original recipe. Turn the dial on the milk container lid (D2)
and conrm the selection by pressing “ OK”.
4. After a few seconds, preparation begins automatically and
an image of the selected drink appears on the display, to-
gether with a progress bar which gradually lls as prepara-
tion progresses.
Please note: general indications when preparing all
milk-based drinks
• “ ESC”: press to interrupt preparation completely and
go back to the homepage.
• “ STOP”: press to interrupt milk or coee delivery and
move on to the next delivery to complete the drink.
• At the end of delivery, to increase the quantity of coee in
the cup, press “ EXTRA”.
16
• Preparation of each cappuccino or milk-based coee can
be customised (see sections “14. Customising the drinks”
and “15. Memorising your personal prole”).
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Once the coee has been made, the appliance is ready to make
the next drink.
10.4 Cleaning the milk container after every use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
Each time you use a milk function, “TURN DIAL TO <CLEAN>
POSITION TO START CLEANING” appears on the display:
1. Leave the milk container (D) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout
(g. 20);
3. Turn the froth adjustment dial (D1) to “CLEAN”. “CLEANING
MILK CONTAINER UNDERWAY PLACE A RECIPIENT UNDER
MILK SPOUT” appears on the display (B) (g. 21) togeth-
er with a bar which gradually lls as cleaning progresses.
Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A9) with a sponge (g. 22).
Please note!
• To prepare a number of cappuccinos or milk-based coees,
clean the milk container after you have prepared the last
drink only. To proceed with making the next drinks, press “
ESC”.
• If you do not clean the milk container, the sym-
bol appears on the display to remind you that it needs
cleaning.
• The milk container can be kept in the refrigerator.
• In some cases, before cleaning you must wait for the appli-
ance to heat up.
11.
MAKING HOT CHOCOLATE
Please note!
When in energy saving mode, a few seconds may elapse before
the rst drink is delivered.
You can make one or two cups of hot chocolate.
Choose CHOCOLATE from the homepage, then proceed as
follows:
1. Lift the carafe lid (E1) (g. 23);
2. Pull the release slide (E6) and extract the carafe funnel (E2)
(g. 23);
3. Make sure the steam spout (E3) and stirrer (E4) are insert-
ed (g. 24);
4. “INSERT STIRRER IN CHOCOLATE CARAFE (STEP 1 OF 4)”
(g. 25): attach the funnel to the carafe, then press “
NEXT”;
5. “POUR MILK OR WATER (STEP 2 OF 4)” (g. 26): to make
one cup of chocolate, pour milk at refrigerator temperature
(or cold water) into the funnel up to the level. To
make two cups or one mug of hot chocolate, pour the milk
(or water) into the funnel up to the level.
When you have added the milk, press “
NEXT”;
6. “ADD CHOCOLATE POWDER THROUGH THE FUNNEL (STEP
3 OF 4)” (g. 27): to make one cup of chocolate, add two
measures (C2) (25 g) of hot chocolate powder. To make two
cups or one mug of hot chocolate, added 4 measures of hot
chocolate powder. When you have added the hot chocolate
powder, press “
NEXT”;
Important!
• Make sure the hole in the funnel shown in g. 28 is clean.
Please note!
• The milk must be poured into the funnel when the steam
spout and stirrer are already in place. Do not exceed the
MAX level marked on the carafe. Increase or reduce the
quantity of hot chocolate powder according to taste.
• To use water instead of milk, follow the instructions for
milk.
• To prepare hot chocolate correctly, rst pour the milk into
the funnel, then add the hot chocolate or cocoa powder as
shown on the hot chocolate carafe lid.
7. “CLOSE THE LID AND INSERT CHOCOLATE CARAFE (STEP 4
OF 4)”: Close the lid (g. 29) and attach the carafe to the
connection nozzle, pushing as far as it will go (g. 30). The
appliance emits a beep (if the beep function is enabled).
The hot chocolate settings screen is displayed;
8.
“SELECT CUPS NUMBER AND DENSITY, PRESS OK TO START”:
press the selection arrows to choose 1 cup (
or 2 cups ()
and the required density (min=
; max =). Press “
OK” to start the function. The appliance starts mixing the
hot chocolate powder then delivers steam to heat it.
17
”
Please note!
• If the hot chocolate powder used does not contain thicken-
er, adjusting the density will have no eect.
• To stop making chocolate, press “
STOP”.
Once the chocolate has been made, the appliance prepares to
make the next drink. The chocolate is ready to be poured into
the cup.
Danger of burns!
• While making the chocolate, the carafe and lid become
very hot. Hold by the handle only to remove the carafe and
pour the chocolate.
• While making the hot chocolate, it is normal for steam to
come out of the holes in the chocolate carafe lid.
• Heating the milk causes splashes inside the carafe. This is
normal.
• The quantity of hot chocolate in the cup varies according to
the density selected. The quantity is less with a high densi-
ty than with a low density.
12. DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Press “
HOT WATER”. The corresponding image ap-
pears on the display (B), together with a progress bar
which lls gradually as preparation proceeds;
4. The machine delivers about 250 ml of hot water, then
delivery stops automatically. To interrupt delivery of hot
water manually, press “ STOP” .
Please note!
• If “Energy Saving” mode is active, you may have to wait a
few seconds before the hot water is delivered.
• Preparation of hot water can be customised (see sections
“14. Customising the drinks” and “15. Memorising your
personal prole”).
13. STEAM DELIVERY
Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Press “ STEAM”. The corresponding image appears
on the display (B), together with a progress bar which lls
gradually as preparation proceeds and after a few seconds,
steam to heat the liquid is delivered from the hot water/
steam spout;
4. When the required temperature or level of froth is ob-
tained, interrupt steam delivery by pressing “ STOP”.
(You should not deliver steam for more than 3 minutes at a
time);
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the hot water is delivered.
13.1 Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow move-
ments in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
13.2 Clean the hot water/steam spout after use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and de-
liver a little water (see section “12. Delivering hot water”).
Stop delivery of hot water by pressing “ STOP”.
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract (g. 17) by pressing the release button
(C7). Hold the spout with one hand and with the other,
turn the hot water/steam spout and pull it downwards
(g. 31).
3. Also remove the steam connection nozzle by pulling it
downwards (g. 32).
4. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
18
6. Insert the nozzle and hot water/steam spout on the con-
nection nozzle by pushing it upwards and turning it clock-
wise until it is attached.
14. CUSTOMISING THE DRINKS
The aroma (when required) and quantity of the drinks can be
customised.
1. Make sure the prole for which you want to customise the
drink is active;
2. From the homepage, press
(B1);
3. To access the customising screen, choose the drink you
want to customise;
4. “CHOOSE COFFEE AROMA”: Select the required aroma by
pressing or and press “ OK” ;
5. “CUSTOMISING COFFEE QUANTITY, STOP TO SAVE”: Prepa-
ration begins and the appliance displays the quantity
customising screen in the form of a vertical bar. The star
alongside the bar represents the current quantity;
6. When the quantity reaches the minimum quantity you can
set, “ STOP” is displayed.
7. When the required quantity is reached, press “ STOP”.
8. “SAVE NEW SETTINGS?”: Press “YES” or “NO”.
The appliance conrms if the values have been saved or not (de-
pending on the previous selection). Press “ OK”.
The appliance goes back to the homepage.
Please note!
• Cappuccino and milk-based coees: the coee aroma
is saved rst, followed by the quantities of rst milk, then
coee;
• Hot water: the appliance delivers hot water. Press “
STOP” to save the required quantity.
• You can also customise the drinks by connecting with the
DeLonghi Coee Link App.
15. MEMORISING YOUR PERSONAL
PROFILE
The appliance allows you to memorise 6 dierent proles, each
associated with a dierent icon.
The prole displays the drinks most frequently selected from
that prole and the aroma and quantity selections for each drink
are memorised.
To select your personal prole, from the homepage press “
PROFILE 1” (B11), then select another numbered prole.
To enter another prole, press the prole currently in use then
press another prole.
Please note!
• “ GUEST” prole: when you select this prole, you can
deliver drinks with the default settings. The
function
is not active.
• You can rename your personal prole by connecting with
the DeLonghi Coee Link App.
16. CLEANING
16.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coee grounds container (A10);
- drip tray (A14);
- water tank (A16);
- coee spouts (A8);
- pre-ground coee funnel (A4);
- infuser (A19), accessible after opening the infuser door
(A18);
- milk container (D);
- chocolate carafe (E);
- hot water/steam connection nozzle (A9);
- display (B).
Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the coee machine. With De’Longhi superautomatic coee
machines, you need not use chemical products to clean the
machine.
• None of the components of the appliance can be washed in
a dishwasher with the exception of the milk container (D)
and chocolate carafe (E).
• Do not use metal objects to remove encrustations or coee
deposits as they could scratch metal or plastic surfaces.
16.2 Cleaning the machine’s internal circuit
If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
• performing 2-3 rinse cycles by selecting the “Rinse” func-
tion (section “8.1 Rinsing ”;
• delivering hot water for a few seconds (section “12. Deliv-
ering hot water”).
Please note!
After cleaning, it is normal for the grounds container (A10) to
contain water.
16.3 Cleaning the coee grounds container
When “EMPTY GROUNDS CONTAINER” appears on the display
(B), the grounds container must be emptied and cleaned. The
19
appliance cannot be used to make coee until you have cleaned
the grounds container (A10). Even if not full, the empty grounds
container message is displayed 72 hours after the rst coee has
been prepared. For the 72 hours to be calculated correctly, the
machine must never be turned o with the main switch.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray (A11) becomes hot. Wait for it to cool down be-
fore touching it and handle it from the front only.
To clean (with the machine on):
33
• Remove the drip tray
(A14) (g. 33), empty
and clean.
• Empty the grounds con-
tainer (A10) and clean
thoroughly to remove
all residues left on the
bottom. This can be
done using the spat-
ula on the brush (C5)
provided.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coees, the grounds container may ll
up more than expected and clog the machine.
16.4 Cleaning the drip tray
Important!
34
The drip tray (A14) is tted
with a level indicator (A12)
(red) showing the level of
water it contains (g. 34).
Before the indicator pro-
trudes from the cup tray
(A11), the drip tray must be
emptied and cleaned, other-
wise the water may overow
the edge and damage the
appliance, the surface it rests
on or the surrounding area.
To remove the drip tray:
1. Remove the drip tray and the coee grounds container
(A10) (g. 33);
2. Empty the drip tray and grounds container and wash them;
3. Replace the drip tray and grounds container.
16.5 Cleaning the inside of the coee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned o
(see section “7. Turning o”) and unplugged from the mains
power supply. Never immerse the coee machine in water.
35
1. Check regularly (about
once a month) that the
inside of the appliance
(accessible after remov-
ing the drip tray (A14) )
is not dirty. If necessary,
remove coee deposits
with the brush (C5) sup-
plied and a sponge.
2. Remove all the residues
with a vacuum cleaner
(g. 35).
16.6 Cleaning the water tank
1. Clean the water tank (A16) regularly (about once a month)
and whenever you replace the water softener lter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid;
2. Remove the lter (if present) and rinse with running water;
3. Replace the lter (if provided), ll the tank with fresh
water and replace the tank;
4. (Models with water softener lter only) Deliver about
100ml of hot water to reactivate the lter.
16.7 Cleaning the coee spouts
36B
36A
1. Clean the coee spouts
(A8) regularly with a
sponge or cloth (g.
36A);
2. Check that the holes in
the coee spouts are not
blocked. If necessary,
remove coee deposits
with a toothpick (g.
36B).
16.8 Cleaning the pre-ground coee funnel
Check regularly (about once a month) that the pre-ground
coee funnel (A4) is not blocked. If necessary, remove coee
deposits with the brush (C5) supplied.
20
16.9 Cleaning the infuser
The infuser (A19) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see section
“7. Turning o”);
2. Remove the water tank (A16) (g. 3);
3738
PUSH
PUSH
3. Open the infuser door (A18) (g. 37) on the right side of
the appliance;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (g. 38);
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap;
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the
internal support (g. 39), then push the PUSH symbol fully
in until it clicks into place;
3940
Please note!
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in g. 40.
41
PUSH
8. Once inserted, make sure
the two coloured but-
tons have snapped out
(g. 41);
9. Close the infuser door;
10. Put the water tank back.
16.10 Cleaning the milk container
To keep the frother ecient, clean the milk container (D) every
two days as described below:
1. Remove the lid (D2);
2. Remove the milk spout (D5) and intake tube (D4) (g. 42);
3. Turn the froth adjustment dial (D1) anticlockwise to the
“INSERT” position (g. 42) and pull it o upwards;
42
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwasher
safe, placing them in the top basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (g. 43). If necessary, scrape the
groove with a toothpick;
21
4344
5. Rinse inside the froth adjustment dial seat with running
water (g. 44);
6. Check that the intake tube and spout are not clogged with
milk residues;
7. Replace the dial (in correspondence to the word “INSERT”),
spout and milk intake tube;
8. Place the lid back on the milk container (D3).
16.11 Cleaning the hot water/steam connection
nozzle
Each time you prepare milk, clean the connection nozzle (A9)
with a sponge to remove milk residues from the gaskets (g.
22).
16.12 Cleaning the hot chocolate carafe (E)
Clean the carafe each time you make hot chocolate as described
below:
1. Lift the lid (E1) and remove the funnel (E2) by pressing
the release button (E6) and lifting (g. 23);
2. Extract the steam spout (D3) and stirrer (D4);
3. Wash all the components thoroughly with hot water and
mild washing-up liquid.
All components are dishwasher safe, placing them
in the top basket of the dishwasher.
4. Replace all the components in the appliance.
Please note!
It is normal to nd residues on the stirrer while cleaning. These
consist of traces of iron in the cocoa attracted by the magnets
in the stirrer.
17. DESCALING
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer’s guarantee.
Descale the appliance when “DESCALING NEEDED PRESS OK TO
START (~40min)
”: appears on the display (B). To descale
the appliance immediately, press “ OK” and follow the in-
structions from point 4.
To descale the appliance later, press “ ESC”. The symbol
appears on the display to remind you that the appliance needs
descaling.
To access the descaling menu:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
DESCALING” appears on
the display;
3. Press ““ to start the descaling cycle then follow the in-
structions on the display;
45
5
5
5
5
5
45
45
4. “REMOVE WATER SOF-
TENER FILTER” (g. 45):
extract the water tank
(A16), remove the water
softener lter (C4) (if
present) and empty the
water tank. Press “
NEXT”;
46
6
6
46
A
B
AB
+
5. “ADD DE’LONGHI DESCAL-
ER (LEVEL A) AND WATER
(UP TO LEVEL B)” (g. 46);
Pour the descaler into the
tank up to the level A
marked inside the tank
(equal to one 100 ml
pack), then add water
(one litre) up to level B
and put the water tank
back. Press “
NEXT”;
47
6. “EMPTY DRIP TRAY” (g.
47): Remove, empty
and replace the drip tray
(A14) and grounds con-
tainer (A10). Press “
NEXT”;
22
7. “PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
DESCALING”: Place an empty container with a minimum
capacity of 2 litres under the hot water/steam spout (C6)
and coee spouts (A8) (g. 8);
Important! Danger of burns
Hot water containing acid ows out of the hot water/steam
spout. Take care to avoid contact with splashes of this solution.
8. Press “ OK” to conrm that you have added the des-
caling solution. “DESCALING UNDERWAY” appears on the
display. The descale programme starts and the descaler
liquid comes out of the hot water/steam and coee spouts.
A series of rinses and pauses is performed automatically to
remove all the scale residues inside the coee machine;
After about 25 minutes, descaling stops;
9. “RINSE AND FILL WATER TANK UP TO MAX LEVEL” (g. 5):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, ll
with fresh water up to the MAX level and put back in the
appliance;
10. “PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING”: Place the container used to collect the descaler
solution empty under the coee spouts and hot water/
steam spout (g. 8) and press “ OK” ;
11. Hot water is delivered rst from the coee spouts, then
from the hot water/steam spout and “RINSING UNDERWAY”
is displayed;
12. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
48
8
8
8
8
8
48
48
13. “INSERT FILTER INTO ITS
HOUSING” (g. 48). Press
“
NEXT” and extract
the water tank. Replace
the water softener lter if
removed previously;
14. “RINSE AND FILL WATER
TANK UP TO MAX LEVEL”
(g. 5): Fill the tank up to
the MAX level with fresh
water;
15. “INSERT WATER TANK” (g. 6): Put the water tank back in the
appliance;
16.
“PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING”: Place the container used to collect the descaler
solution empty under the hot water/steam spout (g. 8)
and press “ OK” ;
17. Hot water is delivered from the hot water/steam spout and
“RINSING UNDERWAY” is displayed;
18. “EMPTY DRIP TRAY” (g. 45): At the end of rinsing, remove,
empty and replace the drip tray (A14) and grounds con-
tainer (A10). Press “ NEXT”;
18. “DESCALE COMPLETE”: press “ OK”;
19. “FILL TANK WITH FRESH WATER”: empty the container used
to collect the rinse water, remove the water tank and ll
with fresh water up to the MAX level, then put back in the
appliance.
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A10) to contain water.
18. SETTING WATER HARDNESS
The “DESCALE” message is displayed after a period of time es-
tablished according to water hardness.
The machine is set by default for a hardness of “LEVEL 4”. The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
18.1 Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
18.2 Setting water hardness
1. Press “” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
WATER HARDNESS” ap-
pears on the display (B);
soft water
slightly hard water
hard water
very hard water
23
7. Extract the tank (A16) from the appliance and ll with
water.
51
5
5
5
8. “IMMERSE FILTER IN THE
WATER TANK LETTING AIR
BUBBLES ESCAPE” (g.
51): Insert the lter in the
water tank and immerse
it completely for about
ten seconds, sloping it
and pressing it lightly to
enable the air bubbles
to escape. Press “
NEXT”;
9. “INSERT FILTER INTO ITS HOUSING AND PUSH IT DOWN TO
THE BOTTOM”: Insert the lter in the lter housing (A17)
(g. 48) and press as far as it will go. Press “
NEXT”;
10. “INSERT WATER TANK”: Close the tank with the lid (A15),
then replace the tank in the machine.
11. “PLACE 0.5l CONTAINER UNDER SPOUTS, PRESS OK TO FILL
FILTER” (g. 8): Place the container under the hot water
spout (C6) and press
“ OK”. Delivery begins and stops
automatically.
The lter is now active and you can use the coee machine.
19.2 Replacing the lter
Replace the lter (C4) when “REPLACE WATER SOFTENER FIL-
TER, PRESS OK TO START
” appears on the display (B). To
replace the lter immediately, press “ OK” and follow the
instructions from point 4.
To replace the lter later, press “
ESC”. The symbol
appears on the display to remind you that the lter needs
replacing.
To replace the lter, proceed as follows:
1. Extract the tank (A16) and exhausted lter;
2. Remove the new lter from the packaging;
3. Press “
” (B2) to enter the menu;
4. Press <(B10) or > (B8) until “
WATER FILTER” appears on
the display;
5. Press “
“;
6. “ REPLACE FILTER” appears on the display;
7. Press ““;
8. Follow the operations described in the previous section
from point 5.
The lter is now active and you can use the coee machine.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the lter even if
the message has not yet been displayed.
3. To change the level selected, press the symbol itself until
the required level is displayed (Level 1 = soft water; Level 4
= very hard water);
4. Press “
ESC” to go back to the homepage.
The machine is now reprogrammed with the new water hard-
ness setting.
19. WATER SOFTENER FILTER
Certain models are tted with a water softener lter (C4). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
19.1 Installing the lter
1. Remove the lter (C4) from the packaging;
2. Press “
” (B2) to enter the menu;
3. Press <(B10) or > (B8) until “
WATER FILTER” appears on
the display;
4. Press “
“;
49
5. “TURN THE DATE INDICA-
TOR UNTIL THE NEXT 2
MONTHS ARE DISPLAYED”
(g. 49): turn the date
disk to display the next
2 months of use. Press “
NEXT”;
Please note
The lter lasts about two
months if the appliance is
used normally. If the coee
machine is left unused with
the lter installed, it will last a maximum of three weeks.
50
6. “RUN WATER INTO FILTER
HOLE UNTIL IT COMES
OUT FROM OPENINGS”
(g. 50): To activate
the lter, run tap water
through the hole in the
lter as shown in the
gure until water comes
out of the openings at the
side for more than a min-
ute. Press “
NEXT”;
24
19.3 Removing the lter
Replace the lter (C4) when “REPLACE WATER SOFTENER FILTER,
PRESS OK TO START
” appears on the display (B). To re-
place the lter immediately, press “ OK” and follow the in-
structions from point 3.
To replace the lter later, press “
ESC”. The symbol
appears on the display to remind you that the lter needs
replacing.
To use the appliance without the lter, proceed as follows:
1. Extract the tank (A16) and exhausted lter;
2. Press “
”(B2) to enter the menu;
3. Press <(B10) or > (B8) until “
WATER FILTER” appears on
the display;
4. Press ““;
5. “
REMOVE FILTER” appears on the display;
6. Press “”;
7. “
CONFIRM REMOVE FILTER”: press
“ OK” (or
press
“ ESC” to go back to the settings menu);
8. “ REMOVE FILTER COMPLETED”: the change has
been saved. Press “ OK” to go back to the homepage.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the lter even if
the message has not yet been displayed.
20. TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10 A
Power: 1450 W
Pressure: 1,5 MPa (15 bar)
Water tank capacity: 2 l
Size LxDxH: 260x480x375 mm
Cord length: 1750 mm
Weight: 12,4 kg
Beans container capacity: 400 g
The appliance complies with the following EC
directives:
• European Standby Regulation 1275/2008
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
21. DISPOSAL
The appliance must not be disposed of with house-
hold waste, but taken to an authorised waste separa-
tion and recycling centre.
22. DISPLAYED MESSAGES
DISPLAYED MESSAGE POSSIBLE CAUSE SOLUTION
FILL TANK WITH FRESH
WATER
Insucient water in the tank (A16).Fill the tank with water and/or insert it cor-
rectly, pushing it as far as it will go until it
clicks into place.
INSERT WATER TANK
The tank (A16) is not correctly in place.Insert the tank correctly and press as far as it
will go.
25
EMPTY GROUNDS CONTAINERThe grounds container (A10) is full.
Empty the grounds container and drip tray
(A14), clean and replace. Important: when
removing the drip tray, the grounds container
MUST be emptied, even if it contains few groun-
ds. If this is not done, when you make the next
coees, the grounds container may ll up more
than expected and clog the machine.
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not
been replaced (A10).
Remove the drip tray (A14) and insert the
grounds container.
ADD PREGROUND COFFEE
MAXIMUM ONE MEASURE
ESC
With the “pre-ground coee” function selected,
pre-ground coee has not been poured into the
funnel (A4).
Place pre-ground coee in the funnel (g. 13)
and repeat delivery
ADD PREGROUND COFFEE
MAXIMUM ONE MEASURE
OK
A LONG coee with pre-ground coee has been
requested
Place pre-ground coee in the funnel (A4) (g.
13) and press “
OK” to continue and com-
plete delivery.
FILL BEANS CONTAINER
ESC
The coee beans have run out.Fill the beans container (A3) (g. 11).
The pre-ground coee funnel (A4) is clogged.Empty the funnel with the help of the brush
(C5) as described in section “16.8 Cleaning the
pre-ground coee funnel”.
26
GROUND TOO FINE. ADJUST
MILL 1 CLICK WHILE IN
OPERATION
ESC
The grinding is too ne and the coee is delive-
red too slowly or not at all.
Repeat coee delivery and turn the grin-
ding adjustment dial (A5) (g. 13) one click
clockwise towards “7” while the coee mill is
in operation. If after making at least 2 coees
delivery is still too slow, repeat the correction
procedure, turning the grinding adjustment
dial another click until delivery is correct (see
section “9.3 Adjusting the coee mill”). If the
problem persists, make sure the water tank
(A16) is fully inserted.
If the water softener lter (C4) is present, an
air bubble may have been released inside the
circuit, obstructing delivery.
Insert the hot water/steam spout (C6) in the
appliance and deliver a little water until the
ow becomes regular.
SELECT A MILDER TASTE
OR REDUCE PREGROUND
COFFEE QUANTITY
ESC
Too much coee has been used.
Select a milder taste by pressing “
AROMA” (B6) or reduce the quantity of pre-
ground coee (maximum 1 measure).
INSERT WATER SPOUT
The hot water spout (C6) is not inserted or is
inserted incorrectly
Insert the water spout as far as it will go.
INSERT MILK CONTAINER
The milk container (D) is not inserted correctly.Insert the milk container as far as it will go (g.
18).
INSERT INFUSER ASSEMBLY
PUSH
The infuser (A19) has not been replaced after
cleaning.
Insert the infuser as described in section “16.9
Cleaning the infuser”.
27
PRESS OK TO START FILLING
PROCESS
OK
The water circuit is empty
Press “
OK” to deliver water from the spout
(C6) until it ows out normally.
If the problem persists, make sure the water
tank (A16) is fully inserted.
PRESS OK TO START CLEANING
PROCESS OR TURN MILK
FROTH ADJUSTMENT DIAL
OK
The milk container has been inserted with
the froth adjustment dial (D1) in the “CLEAN”
position.
To proceed with the CLEAN function press
“
OK”, or turn the froth adjustment dial to one of
the milk positions.
TURN DIAL TO <CLEAN> POSI-
TION TO START CLEANING
CLEAN
ESC
Milk has been delivered recently and the tubes
inside the milk container must be cleaned (D).
Turn the froth adjustment dial (D1) to CLEAN
(g. 20).
TURN THE MILK FROTH
ADJUSTMENT DIAL TO MILK
POSITION
The milk container has been inserted with
the froth adjustment dial (D1) in the “CLEAN”
position.
Turn the dial to the required froth position.
DESCALING NEEDED PRESS
OK TO START ~40MIN
ESC OK
The machine must be descaled.
Press “
OK” to start descaling or “ ESC”
to descale later. The descaling procedure descri-
bed in section “17. Descaling” needs to be per-
formed as soon as possible.
28
REPLACE WATER SOFTENER FIL-
TER PRESS OK TO START
ESC OK
The water softener lter (C4) is exhausted.
Press “
OK” to replace or remove the lter,
or “ ESC” to carry out the procedure later.
Follow the instructions in section “19. Water
softener lter”.
GENERAL ALARM. REFER
TO USER MANUAL / SMART
COFFEE APP
The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,
as described in section “16. Cleaning”. If the
message is still displayed after cleaning, con-
tact a service centre.
The appliance needs descaling and/or the lter
(C4) must be replaced.
The descaling procedure described in section
“17. Descaling” needs to be performed and/or
the lter needs replacing or removing as descri-
bed in section “19. Water softener lter”.
The tubes inside the milk container (C) must be
cleaned.
Turn the froth adjustment dial (D1) to CLEAN
(g. 20).
The lter (C4) must be replaced. Replace or remove the lter as described in
section “19. Water softener lter”.
The machine must be descaled.The descaling procedure described in section
“17. Descaling” needs to be performed as soon
as possible.
The auto-start function is enabled. To disable the function, proceed as described in
section “8.6 Auto-start
”.
Energy saving is enabled. To disable energy saving, proceed as described
in section “8.9 Energy saving
”.
The appliance is connected to a device via
bluetooth.
29
PROBLEM POSSIBLE CAUSE SOLUTION
The coee is not hot.The cups were not preheated.Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The infuser has cooled down because
2/3 minutes have elapsed since the last
coee was made.
Before making the coee, heat the infuser by
rinsing using the rinse function (see section
“8.1 Rinsing
”).
A low coee temperature is set.
Set a higher coee temperature in the menu
(see section “8.10 Coee temperature ” ).
The coee is weak or not creamy
enough.
The coee is ground too coarsely.Turn the grinding adjustment dial (A5) one
click anticlockwise towards “1” while the cof-
fee mill is in operation (g. 10). Continue one
click at a time until coee delivery is satisfac-
tory. The eect is only visible after delivering
2 coees (see section “9.3. Adjusting the coee
mill”).
The coee is unsuitable.Use pre-ground coee for espresso machines.
The coee is delivered too slowly or a
drop at a time.
The coee is ground too nely.Turn the grinding adjustment dial (A5) one
click clockwise towards “7” while the coee
mill is in operation (g. 10). Continue one click
at a time until coee delivery is satisfactory.
The eect is only visible after delivering 2
coees (see section “9.3. Adjusting the coee
mill”).
Coee does not come out of one or
both of the spouts.
The coee spouts (A8) are blocked.Clean the spouts with a toothpick (g. 36B).
The appliance does not come onThe power cord (C8) connector is not
inserted correctly.
Insert the connector as far as it will go in the
socket at the back of the appliance (g. 1).
It is not plugged into the mains socket.Plug into the mains socket (g. 1).
The main switch (A21) is not turned on.Press the main switch (g. 2).
The infuser cannot be extractedThe appliance has not been turned o
correctly
Turn the appliance o by pressing the (A7)
(see section “7. Turning o”).
The milk does not come out of the
milk spout (D5)
The lid (D2) of the milk container lid
(D) is dirty
Clean the milk container lid as described in sec-
tion “16.10 Cleaning the milk container”.
23. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
30
The milk contains large bubbles and
squirts out of the milk spout (D5) or
there is little froth
The milk is not cold enough or is not
semi-skimmed.
Use skimmed or semi-skimmed milk at refrige-
rator temperature (about 5° C). If the result is
not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incor-
rectly adjusted.
Adjust following the instructions in section
“10. Making cappuccinos and milk-based
coees”.
The milk container lid (D2) or froth
adjustment dial (D1) are dirty.
Clean the milk container lid and dial as de-
scribed in section “16.10 Cleaning the milk
container”.
The hot water/steam connection noz-
zle (A9) is dirty
Clean the connection nozzle as described in
section “16.11 Cleaning the hot water/steam
connection nozzle”.
The cup warmer is hot, even though it
has been disabled
A number of drinks have been prepared
in rapid succession
The chocolate is not suciently denseThe hot chocolate powder used does
not contain thickener.
Change the type of powder used.
The highest density has not been se-
lected.
Select the highest density in the correspon-
ding screen.
The quantities of milk and hot chocola-
te powder are not correct.
Follow the instructions in section "11. Making
hot chocolate"
The chocolate is cold or there are
lumps
The stirrer (E4) and steam spout (E3)
are not inserted correctly in the funnel
(E2).
Insert the stirrer and steam spout on the fun-
nel.
The instructions have not been follo-
wed.
Pour the milk/water into the funnel (E2) rst,
followed by the hot chocolate powder.
During cleaning, there are traces of
black on the stirrer (E4)
The magnets in the stirrer attract traces
of iron naturally present in the hot cho-
colate powder.
Clean as described in section "16.12 Cleaning
the hot chocolate carafe (E)".
31
24. ELECTRICAL REQUIREMENTS UK ONLY
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt
about your supply contact your local electricity company.
The exible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not t the socket outlets in your home, it should be cut o and replaced with a suitable plug, following the procedure outlined
below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might nd it and
plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched o when the machine is not in use.
IMPORTANT: the wires in the mains lead tted to this appliance are coloured in accordance with the following code:
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWN LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth
symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the
plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualied electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualied electrician and should only be replaced
with a exible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be retted. If the fuse cover is lost, the plug must not be used until a replacement cover is
obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always
state this colour when ordering a replacement fuse cover. Only 13amp replacement fuses which are asta approved to B.S. 1362 should be tted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for DeLonghi ECAM 650.75 - Prima Donna Elite at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of DeLonghi ECAM 650.75 - Prima Donna Elite in the language / languages: English as an attachment in your email.
The manual is 1,93 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of DeLonghi ECAM 650.75 - Prima Donna Elite
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.