Manual DeLonghi ECAM 350.55 - Dinamica (page 15 of 21) (English)

709060

Zoom out

Zoom in

1/21

If the coee machine is left unused with the lter installed, it

will last a maximum of three weeks.

3. To activate the lter, run tap water through the hole in the

lter as shown in g. 35 until water comes out of the open-

ings at the side for more than a minute.;

35 36

0,5 L

4. Extract the tank (A17) from the appliance and ll with

water;

5. Insert the lter in the water tank and immerse it complete-

ly for about ten seconds, sloping it and pressing it lightly to

enable the air bubbles to escape (g. 36).

6. Insert the lter in the lter housing (A18) and press as far

as it will go (g. 37);

7. Close the tank with the lid (A16) (g. 38), then replace the

tank in the machine;

37 38

When you install the lter, you must notify the appliance of its

presence.

8. Press (B6) to enter the "Settings" menu;

9. Press the selection arrows (B2 and B4) until "Maintenance"

is displayed between the two lines. Press OK;

10. Press the selection arrows until "Install lter" is displayed,

then press OK;

11. Conrm?": press OK;

12. "Hot water, Conrm?": Position a container under the hot

water spout (C6) (min. capacity: 500 ml), then press OK;

13. The appliance begins hot water delivery and the message

"Please wait" is displayed;

14. After the ow of hot water stops, the appliance automati-

cally resets to "Ready for coee" status.

The lter is now active and you can use the coee machine.

17.2 Replacing the lter

Replace the lter (C4) when "Replace lter, ESC to cancel, OK to

replace" appears on the display (B1). To replace immediately,

press OK (B3) and follow the instructions from point 8. To re-

place later, press ESC (B5). The symbol on the display reminds

you that the lter needs replacing.

To replace the lter, proceed as follows:

1. Extract the tank (A17) and exhausted lter;

2. Take the new lter out of its packet and proceed as illus-

trated in points 2, 3, 4, 5, 6 and 7 in the previous section;

3. Press (B6) to enter the "Settings" menu;

4. Press the selection arrows (B2 and B4) until "Maintenance"

is displayed between the two lines. Press OK;

5. Press the selection arrows until "Replace lter" is dis-

played, then press OK;

6. Conrm?": press OK;

7. "Hot water, Conrm?": Position a container under the hot

water spout (C6) (min. capacity: 500 ml), then press OK;

8. The appliance begins hot water delivery and the message

"Please wait" is displayed;

9. After the ow of hot water stops, the appliance automati-

cally resets to "Ready for coee" status.

The new lter is now active and you can use the coee machine.

Please note!

After two months (see date indicator) or when the appliance has

not been used for 3 weeks, you should replace the lter even if

the message has not yet been displayed.

17.3 Removing the lter

If you want to use the appliance without the lter (C4), you

must remove it and notify the appliance of its removal. Proceed

as follows:

1. Extract the tank (A17) and exhausted lter;

2. Press (B6) to enter the "Settings" menu;

3. Press the selection arrows (B2 and B4) until "Maintenance"

is displayed between the two lines. Press OK;

4. Press the selection arrows until "Remove lter" is dis-

played, then press OK;

5. "Conrm?": press OK to conrm removal. The appliance

goes back to the "Maintenance" menu;

Press /ESC (B5) to exit the menu.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi ECAM 350.55 - Dinamica in the language / languages: English as an attachment in your email.

The manual is 4.46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi ECAM 350.55 - Dinamica

DeLonghi ECAM 350.55 - Dinamica User Manual - German - 22 pages

DeLonghi ECAM 350.55 - Dinamica User Manual - Dutch - 21 pages

DeLonghi ECAM 350.55 - Dinamica User Manual - French - 20 pages

DeLonghi ECAM 350.55 - Dinamica User Manual - Italian - 27 pages

DeLonghi ECAM 350.55 - Dinamica User Manual - Spanish - 21 pages

DeLonghi ECAM 350.55 - Dinamica Additional guide - All languages - 6 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeLonghi ECAM 350.55 - Dinamica Manual

Product: