821516

DeLonghi Dinamica Plus - ECAM380.95 Manual

18
Zoom out
Zoom in
Previous page
1/28
Next page
18
set intervals to remove the scale residues from inside the
coee machine;
After about 15 minutes, descaling stops;
10. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 3):
the appliance is now ready for a process of rinsing with
fresh water. Empty the container used to collect the des-
caler solution. Remove the water tank from the machine,
empty it and rinse under running water, then ll with clean
water up to the MAX level and reposition it in the machine.
11. "POSITION 2l CONTAINER OK TO START RINSING": Repo-
sition the container used to collect the descaler solution,
empty, under the coee spouts and hot water spout and
press ;
12. Hot water is delivered rst from the coee spouts then
from the hot water spout and the message "RINSING UN-
DERWAY, PLEASE WAIT" is displayed;
13. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
14. (If the lter is installed) "INSERT FILTER IN ITS HOUSING"
(g. 36). Press and take out the water tank:
replace the water softener lter, if removed previously;
36
15. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 3): Fill
the tank up to the MAX level with fresh water;
16. "INSERT WATER TANK" (g. 4): Reposition the water tank
in the machine.
17. "POSITION 2l CONTAINER" "OK TO START RINSING": Repo-
sition the container used to collect the descaler solution,
empty, under the hot water spout (g. 8) and press
.
18. Hot water is delivered from the hot water/steam spout
and the message "RINSING UNDERWAY, PLEASE WAIT" is
displayed;
19. "EMPTY DRIP TRAY" (g. 21): At the end of the second
rinse, empty the container used to collect the rinsing
water, remove and empty the drip tray (A15) and grounds
container (A11) and return them to the machine: press
;
20. "DESCALE COMPLETE": press ;
21. "FILL TANK WITH FRESH WATER": remove and top up the
water tank with fresh water to the MAX level and put back
in the machine.
The descaling cycle is now complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. elec-
trical power failure), when power is restored the appliance
will prompt for the cycle to be completed.
• Water may nd its way into the grounds container (A11)
during the descale cycle: this is quite normal.
• If the water tank has not been lled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been complete-
ly eliminated from the machine's internal circuits. Before
starting the rinse, remember to empty the drip tray.
14.
SETTING WATER HARDNESS
The descaling alert is displayed after a period of operation es-
tablished according to water hardness.
The machine can also be programmed according to the actual
hardness of the local water supply, so that the descaling proce-
dure will be required less frequently.
14.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator strip (D1)
from its pack.
2. Immerse the paper completely in a glass of water for about
one second.
3. Remove the strip from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares appear, depending
on the hardness of the water. Each square corresponds to
one level.
14.2 Setting water hardness
1. Access the menu as described in section "6.1 Access the
menu";
2. Press "WATER HARDNESS";
3. Carry out the procedure described in the previous section
to measure the water hardness;
4. "WATER HARDNESS" "CURRENT VALUE UNDERLINED": Press
the level measured previously as indicated in the following
table: (Level 1 = soft water; Level 4 = very hard water);
Indicator paper Water hardness
Level 1 - soft water
Level 2 - slightly hard
water
Level 3 - hard water
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi Dinamica Plus - ECAM380.95 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi Dinamica Plus - ECAM380.95 in the language / languages: English as an attachment in your email.

The manual is 10.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi Dinamica Plus - ECAM380.95

DeLonghi Dinamica Plus - ECAM380.95 User Manual - German - 32 pages

DeLonghi Dinamica Plus - ECAM380.95 User Manual - Dutch - 124 pages

DeLonghi Dinamica Plus - ECAM380.95 User Manual - French, Italian - 52 pages

DeLonghi Dinamica Plus - ECAM380.95 User Manual - Portuguese, Spanish - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info