687413
17
Zoom out
Zoom in
Previous page
1/21
Next page
22
Ground too ne
Adjust mill
The grinding is too ne and the coee is deliv-
ered too slowly or not at all.
Repeat coee delivery and turn the grinding
adjustment dial (A5) (g. 7) one click clockwise
towards 7 while the coee mill is in operation.
If after making at least 2 coees delivery is
still too slow, repeat the correction procedure,
turning the grinding adjustment dial another
click until delivery is correct (see section “10.1
Adjusting the coee mill”. If the problem per-
sists, make sure the water tank (A17) is fully
inserted.
If the water softener lter (C4) is present, an
air bubble may have been released inside the
circuit, obstructing delivery.
Insert the hot water spout (C6) in the appli-
ance and deliver a little water until the ow
becomes regular.
Less coee Too much coee has been used.
Select a lighter taste by pressing (B7) or
reduce the quantity of pre-ground coee.
Insert water spout The hot water spout (C6) is not inserted or is
inserted incorrectly.
Fully insert the hot water spout (g. 4).
Insert milk container The milk container (D) is not inserted correctly. Insert the milk container as far as it will go (g.
16).
Insert infuser assembly The infuser (A20) has not been replaced after
cleaning.
Insert the infuser as described in section “14.9
Cleaning the infuser”.
Water circuit empty
Fill water circuit
Hot water
Conrm?
The water circuit is empty. Press OK (B3) to deliver water from the spout
(C6) until it ows out normally. If the problem
persists, make sure the water tank (A17) is fully
inserted.
Press OK to CLEAN The milk container (D) has been inserted with
the froth adjustment dial (D1) in the "CLEAN"
position.
To proceed with the CLEAN function press OK
or turn the froth adjustment dial to another
position.
Set dial to CLEAN
ESC to cancel
Milk has been delivered recently and the tubes
inside the milk container (D) must be cleaned.
Turn the froth adjustment dial (D1) to CLEAN
(g. 19).
Turn froth adjustment dial The milk container (D) has been inserted with
the froth adjustment dial (D1) in the "CLEAN"
position.
Turn the froth adjustment dial to one of the
milk froth positions.
Descale
ESC to cancel
OK to descale
(45 minutes)
The machine must be descaled. The descaling procedure described in section
“15. Descaling” needs to be performed.
Replace lter
ESC to cancel
OK to replace
The water softener lter (C4) is exhausted. Replace the lter or remove it as described in
section “17. Water softener lter”.
General alarm The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,
as described in section “14. Cleaning”. If the
message is still displayed after cleaning, con-
tact a service centre.
17


Need help? Post your question in this forum.

Forumrules
1

Forum

delonghi-dinamica-ecam-350.55

Reset search

  • hallo, ingeprgrammeerde koffie kan dat ook veranderd worden of teruggebracht naar andere waarde<
    MVG Fred Submitted on 23-10-2020 at 10:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi Dinamica ECAM 350.55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi Dinamica ECAM 350.55 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi Dinamica ECAM 350.55

DeLonghi Dinamica ECAM 350.55 User Manual - German - 22 pages

DeLonghi Dinamica ECAM 350.55 User Manual - Dutch - 21 pages

DeLonghi Dinamica ECAM 350.55 User Manual - French - 20 pages

DeLonghi Dinamica ECAM 350.55 User Manual - Italian - 27 pages

DeLonghi Dinamica ECAM 350.55 User Manual - Spanish - 21 pages

DeLonghi Dinamica ECAM 350.55 Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info