709059

DeLonghi Dinamica - ECAM 350.15.B Manual

18
Zoom out
Zoom in
Previous page
1/24
Next page
17
5. Pour the descaler (C3) into the tank up to level A (corre-
sponding to a 100ml pack) marked on the inner surface of
the tank, then add a litre of water up to level B (g. 24) and
put the water tank back in the appliance;
6. Place a container with a minimum capacity of 1.8 litres
under the cappuccino maker (A20) and coee spouts (A19)
(g. 25);
Important! Danger of burns
Hot water containing acid ows from the cappuccino maker and
coee spouts. Take care to avoid contact with splashes of this
solution.
7. Press the OK icon to conrm that you have added
the descaler solution. The descaling procedure begins;
8. After a few minutes, the ESC icon (B14) ashes to
indicate the steam/hot water dial (A22) must be
turned to the I
position;
9. When the dial has been turned to the l position, the des-
cale programme starts and the descaler liquid comes out
of the cappuccino maker. A series of rinses and pauses are
performed automatically to remove all the scale residues
inside the coee machine;
After about 35 minutes, the appliance interrupts descaling and
the light (B3) ashes.
10. The appliance is now ready for rinsing through with clean
water. Empty the container used to collect the descaler
solution. Extract the water tank, empty, rinse under run-
ning water, ll with fresh water up to the MAX level and
put back in the appliance;
11. Place the container used to collect the descaler solution
empty under the coee spouts and cappuccino maker (g.
25);
12. Press the OK icon: ESC ashes to indicate
the steam/hot water dial must be turned to the O
position;
13. Turn the steam/hot water dial to the O position to
start rinsing. Hot water comes out of the coee spouts;
14. After a preset time, ESC ashes. Turn the dial to the
I position. Delivery continues from the cappuccino maker.
When the water in the tank has run out, the light
(B3) comes on;
15. The appliance is now ready for a second rinse with clean
water. Empty the container used to collect the rinse water.
Extract the water tank, empty, rinse under running water,
ll with fresh water up to the MAX level, replace the water
softener lter (if previously removed) and put back in the
appliance;
16. Place the container used to collect the rinsing water empty
under the cappuccino maker;
17. Press the OK icon. The appliance begins rinsing
again from the cappuccino maker only;
18. When the water in the tank has run out, the light
ashes;
19. Empty the container used to collect the rinse water, re-
move the water tank and ll with fresh water up to the
MAX level, then put back in the appliance. The ESC
icon ashes;
20. Turn the dial to the 0 position;
21. Empty and replace the drip tray (A15) and grounds con-
tainer (A11).
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A11) to contain water;
• If the water tank has not been lled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been completely
eliminated from the machine's internal circuits.
20. SETTING WATER HARDNESS
The light (B5) comes on after a period of time established
according to water hardness.
The machine is set by default for a hardness level of 4. The ma-
chine can also be programmed according to the hardness of
the mains water in the various regions so that the mquaachine
needs to be descaled less often.
20.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions);
2. Immerse the paper completely in a glass of water for one
second;
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to 1
level;
Indicator paper Water
hardness
Corresponding
setting
low
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi Dinamica - ECAM 350.15.B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi Dinamica - ECAM 350.15.B in the language / languages: English as an attachment in your email.

The manual is 12,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi Dinamica - ECAM 350.15.B

DeLonghi Dinamica - ECAM 350.15.B User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info