Manual Defort DSP-400CN (page 6 of 64) (All languages)

555818

Zoom out

Zoom in

1/64

!IF IN DOUBT CONSULT

A QUALIFIED ELECTRICIAN!

All electrical connections e.g. extension cable, must

be of an approved waterproof type for outdoor use.

Exten sion cables must be three-core, one of which is

EARTH.

Always fully unwind extension cables before use.

Connection to the mains power supply must be via an

approved residual current device (RCD), with a residu-

al operating current not exceeding 30mA.

MAINTENANCE

There are no user serviceable parts in this appli-

ance. If the appliance appears to be blocked, switch

off the power at the mains, remove the plug from the

socket and check the appliance for blockages (see

‘Blockages’).

BLOCKAGES

If you suspect the pump has become blocked, switch

off the power at the mains socket remove the plug and

exa mine the turbine. The turbine can be accessed by

remo ving the securing screws in the base and/or sub

base. Alternately try reaching the suspected blockage

through the outlet pipe in the side of the pump.

Always ﬂ ush through with clean water after every use.

IMPORTANT: During maintenance or cleaning never

rest the appliance of the on the turbine (impeller).

GENERAL USE

• This pump is NOT designed for continuous opera-

tion e.g. as a swimming pool or pond circulation

pump.

• If used as an intermittent pump to circulate water

in an ornamental pond it must be sited in a sump

or behind a suitable barrier to stop pond life being

suc ked into it.

• Use a rope to lower the pump into deep water -nev-

er lower the pump by its power cord or delivery pipe

at anytime.

• Ensure there are no obstructions around the inlet

openings around the base of the pump. The inlet

ope nings must be clear of mud or sludge at the bot-

tom of a pool.

• It would be advisable to stand the pump of a solid

plat form at the bottom of the pool to keep it upright,

if practical to do so.

• If the pump is used to drain a swimming pool it must

only be used when the pool is completely empty of

people.

• It is important that the ﬂ oating switch is allowed to

reach its ON height in the water. It must also be

able to ﬂ oat down without obstruction in order for it

to switch off when required.

• After use allow the pump to run using clean water

for 2-3 minutes in order to remove residues and

parti cles that may have accumulated in the pump

and out let hose.

NOTE:

If the level of water becomes to low, any sludge in the

shaft will dry out more quickly and this may prevent

the pump from restarting. To ensure the pump works

efﬁ ciently the bottom of the shaft must be kept free of

sludge as far as possible and cleaned on a regular ba-

sis when not in use.

OPERATING INSTRUCTIONS

Automatic Operation

When the pump is lowered into the water and the pow-

er is switched on, it will start to operate as soon as the

ﬂ o ating switch reaches the minimum activation height

in the water.

Remember: The pump must be carried by, and placed

in the water using the carry handle or if the water is

deep, be lowered on a rope tied to the carry handle.

Manual Operation

Where manual operation is preferred, the motor can be

activated by raising the ﬂ oating switch by hand (ON) or

lowering it by hand (OFF).

Ensure the distance between the ﬂ oat switch and the

latch holder is not too small as to restrict the up and

down movement of the ﬂ oat switch.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Defort DSP-400CN in the language / languages: All languages as an attachment in your email.

The manual is 2,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Defort DSP-400CN Manual

Product: